Dis-

Parameter Name

 

Set-

 

Range

Default

Appears If

play

 

Description

 

tings

 

 

 

 

[iP;A3]

Diagnostics Menu

 

 

0 to 255

 

None

the controller in-

[iP.A3]

IP Actual Address Part 3

 

 

 

 

 

cludes EtherNet/

 

Display the third part of this

 

 

 

 

 

IP (PM6 _ _ _ _-

 

controller's IP address.

 

 

 

 

 

3AA _ A _ _).

 

 

 

 

 

 

 

 

[iP;A4]

Diagnostics Menu

 

 

0 to 255

 

None

the controller in-

[iP.A4]

IP Actual Address Part 4

 

 

 

 

 

cludes EtherNet/

 

Display the fourth part of this

 

 

 

 

 

IP (PM6 _ _ _ _-

 

controller's IP address.

 

 

 

 

 

3AA _ A _ _).

 

 

 

 

 

 

 

[C;LEd]

Diagnostics Menu

 

 

[`oFF] Off

 

 

[C.LEd]

Communications Indicator

 

 

[Con1] Channel 1

 

 

 

Light

 

 

 

[Con2] Channel 2

 

 

 

Select which channel the Commu-

 

 

 

 

 

[Both] Both

 

 

 

nications Activity indicator light

 

 

 

 

 

 

 

 

 

 

 

 

will monitor.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[`CAL]

 

[```1]

[```2]

 

 

 

 

[FCty]

 

[`CAL]

[`CAL]

 

 

 

 

Calibration Menu

Calibration 1

Calibration 2

(input 2 appears if PM6 _ _ _ _-_ [R, T or L] _ _ A _ _)

 

 

 

 

 

 

 

[`Mu]

Calibration Menu (1 or 2)

 

 

-1,999.000 to 9,999.000

 

always

[ Mv]

Electrical Measurement

 

 

 

 

 

 

 

Read the raw electrical value

 

 

 

 

 

 

 

for this input in the units cor-

 

 

 

 

 

 

 

responding to the Sensor Type

 

 

 

 

 

 

 

(Setup Page, Analog Input Menu)

 

 

 

 

 

 

setting.

 

 

 

 

 

 

 

[ELi;o]

Calibration Menu (1 or 2)

 

 

-1,999.000 to 9,999.000

0.0

always

[ELi.o]

Electrical Input Offset

 

 

 

 

 

 

 

Change this value to calibrate the

 

 

 

 

 

 

low end of the input range.

 

 

 

 

 

 

 

 

 

 

 

 

 

[ELi;S]

Calibration Menu (1 or 2)

 

 

-1,999.000 to 9,999.000

1.0

always

[ELi.S]

Electrical Input Slope

 

 

 

 

 

 

 

Adjust this value to calibrate the

 

 

 

 

 

 

 

slope of the input value.

 

 

 

 

 

 

 

 

 

 

 

 

 

[ELo;o]

Calibration Menu (1 or 2)

 

 

-1,999.000 to 9,999.000

0.0

the controller has

[ELo.o]

Electrical Output Offset

 

 

 

 

 

process outputs:

 

Change this value to calibrate the

 

 

 

 

(PM6_ _F_- _ _ _

 

low end of the output range.

 

 

 

 

 

_A_ _) or (PM6_

 

Menu 2 calibrates output 3.

 

 

 

 

 

_ _ _-_ _F_A_ _)

 

 

 

 

 

 

 

[ELo;S]

Calibration Menu (1 or 2)

 

 

-1,999.000 to 9,999.000

1.0

the controller has

[ELo.S]

Electrical Output Slope

 

 

 

 

 

process outputs:

 

Adjust this value to calibrate the

 

 

 

 

 

(PM6_ _F_- _ _ _

 

slope of the output value.

 

 

 

 

 

_A_ _) or (PM6_

 

Menu 2 calibrates output 3.

 

 

 

 

 

_ _ _-_ _F_A_ _)

 

 

 

 

 

 

 

 

 

Note: Some values will be rounded off to fit in the four-character display. Full values can be read with another interface. If there is only one instance of a menu, no submenus will appear.

Watlow EZ-ZONE®PM Integrated Controller

• 52 •

Chapter 8 Factory Page