Manuals / Brands / Computer Equipment / Network Card / Watlow Electric / Computer Equipment / Network Card

Watlow Electric EZ-ZONE PM DeclarationDeclarationofofConformityConfor, A1:1998, A2:2002, Class B Emissions, 73/23/EEC Low-VoltageDirective, Series EZ Zone PM (Panel Mount)

1 80

Download 80 pages, 3.27 Mb

DeclarationDeclarationofofConformityConfor

Series EZ Zone PM

Watlow Winona, Inc.

1241 Bundy Blvd.

Winona, MN 55987 USA

Declares that the following product:

Designation:	Series EZ Zone PM (Panel Mount)
Model Numbers:	PM (3 or 6)(Any letter or number) – (1, 2, 3 or 4)(A, C, E, F or K)
	(A, C, H, J or K)(Any letter or number) – (Any letter or number)
	(A, C, E, F or K)(A, D, J or K)(Any two letters or numbers)
Classification:	Temperature control, Installation Category II, Pollution degree 2
Rated Voltage and Frequency:	100 to 240 V~ ac 50/60 Hz or 15 to 36 Vt dc/24 V~ ac 50/60 Hz
Rated Power Consumption:	10 VA maximum.
Environmental Rating:	Front Panel IP66

Meets the essential requirements of the following European Union Directives by using the relevant standards show below to indicate compliance.

2004/108/EC Electromagnetic Compatibility Directive

EN 61326	1997	A1:1998	Electrical equipment for measurement, control and
		A2:2002	laboratory use – EMC requirements (Industrial Immunity,
			Class B Emissions
EN 61000-4-2	1996	A1, A2, 2001	Electrostatic Discharge Immunity
EN 61000-4-3	2002	A1, A2, 2005	Radiated Field Immunity
EN 61000-4-4	2004		Electrical Fast-Transient / Burst Immunity
EN 61000-4-5	1995	A1, A2, 2001	Surge Immunity
EN 61000-4-6	1996	A1,A2,A3, 2005	Conducted Immunity
EN 61000-4-11	2004		Voltage Dips, Short Interruptions and Voltage Variations
EN 61000-3-2			Immunity
EN 61000-3-2	2000	ED.2.	Harmonic Current Emissions
EN 61000-3-31	1995	A1, A2, 2002	Voltage Fluctuations and Flicker

1For mechanical relay loads, cycle time may need to be extended up to 30 seconds to meet flicker requirements depending on load switched and source impedance.

	73/23/EEC Low-Voltage Directive
EN 61010-1	2001 Safety Requirements of electrical equipment for measurement, control
	and laboratory use. Part 1: General requirements

Compliant with 2002/95/EC RoHS Directive2002/96/EC WEEE Directive Equipment Requires Recycling

	Raymond D. Feller III			Winona, Minnesota, USA
	Name of Authorized Representative			Place of Issue
	General Manager			August, 2007
	Title of Authorized Representative			Date of Issue

	Signature of Authorized Representative

Watlow EZ-ZONE®PM Integrated Controller

• 76 •

Appendix

Contents

EZ-ZONE® PM User’s Manual Integrated Controller Models Safety Information Warranty Technical Assistance Return Material Authorization (RMA) TC Table of Contents 1Chapter 1: Overview Standard Features and Benefits Inputs Functions Outputs Input Events and Output Events EZ-ZONE® PM Integrated Model 1/16 DIN with a Current Transformer — Input/Output (no communications options 2 to 3) Functions Current Monitoring EZ-ZONE® PM Integrated Model 1/16 DIN with Remote Set Point — Input/Output Remote Set Point Operation EZ-ZONE® PM Integrated Model 1/16 DIN with a Limit — Input/Output EZ-ZONE® PM Integrated Model 1/16 DIN with Expanded Communications — Input/Output Serial Communication Capabilities 2 Chapter 2: Install and Wire Dimensions Installation Removing the Mounted Controller from Its Case Returning the Controller to its Case Chemical Compatibility Terminal Definitions for Slots A and B Terminal Definitions for Slot C Low Power High Power Digital Input or Output Input 1 Thermocouple Input 1 RTD Input 1 Process Input 1 Potentiometer Input 2 Thermocouple Input 2 RTD Input 2 Process Input 2 Potentiometer Input 2 Current Transformer Output 1 Switched DC/Open Collector Output 1 Mechanical Relay, Form C Output 1 Universal Process Output 1 Solid-stateRelay, Form A Output 2 Switched DC Output 2 No-arcRelay, Form A Output 2 Mechanical Relay, Form A Output 2 Solid-stateRelay, Form A Output 3 Switched DC/Open Collector Output 3 Mechanical Relay, Form C Output 3 Universal Process Output 3 Solid-stateRelay, Form A Output 4 Switched DC Output 4 Mechanical Relay, Form A Output 4 Solid-stateRelay, Form A Standard Bus EIA-485Communications Modbus RTU or Standard Bus EIA-485Communications EIA-232/485Modbus RTU Communications EtherNet/IP™ and Modbus TCP Communications DeviceNet™ Communications Wiring a Serial EIA-485Network 3Chapter 3: Keys and Displays Responding to a Displayed Message Attention Codes Navigating the EZ-ZONE® PM Integrated Controller 4Chapter 4: Home Page Changing the Set Point Parameters that appear only in the Home Page 5Chapter 5: Operations Page Navigating the Operations Page Page Page Page Page 6Chapter 6: Setup Page Page Page Page Page Page Page Page Page Page Page Page 7Chapter 7: Profiling Page Navigating the Profiling Page How to Start a Profile Page Page 8Chapter 8: Factory Page Navigating the Factory Page Page Page Page 9Chapter 9: Features Autotuning Manual Tuning Autotuning with TRU-TUNE+® Before Tuning How to Autotune a Loop Calibration Offset Calibration Filter Time Constant Sensor Selection Sensor Backup Set Point Low Limit and High Limit Scale High and Scale Low Duplex No-arcRelay Retransmitting a Process Value or Set Point Cool Output Curve Output Configuration Auto (closed loop) and Manual (open loop) Control On-OffControl Proportional Control Proportional plus Integral (PI) Control Proportional plus Integral plus Derivative (PID) Control Dead Band Variable Time Base Single Set Point Ramping Process and Deviation Alarms Alarm Set Points Alarm Hysteresis Alarm Latching Alarm Silencing Alarm Blocking Using keys and display: Using the software with Standard Bus: Lockout Menu Chapter 10: Appendix Troubleshooting Alarms, Errors and Control Issues Page Page Specifications Operator Interface Dimensions Weight Note: These specifications are subject to change without prior notice Ordering Information for Integrated Controller Models Index Page Page Page DeclarationDeclarationofofConformityConfor Page How to Reach Us Corporate Headquarters Latin America Europe Asia and Pacific