Display |
| Parameter name |
| Set- | Range | Default | Appears If |
|
| Description |
| tings |
|
|
|
|
|
|
|
|
|
|
|
[``Ai] |
| [```1] | [```2] |
|
|
|
|
[oPEr] |
| [``Ai] | [``Ai] |
|
|
| |
Analog Input Menu | Analog Input 1 or | Analog Input 2 | (input 2 appears if PM6 _ _ _ | ||||
|
|
|
|
|
|
| |
[`Ain] | Analog Input (1 or 2) |
|
|
| always | ||
[ Ain] | Process Value |
|
|
|
| ||
| View the process value. |
|
|
|
|
| |
|
|
|
|
|
|
| |
[`i;Er] | Analog Input (1 or 2) |
|
| [nonE] None | None | always | |
[ i.Er] | Error Status |
|
| [OPEn] Open |
|
| |
| View the cause of the most recent error. If the |
| [Shrt] Shorted |
|
| ||
| [Attn] message is [Er;i1] or [Er;i2], this param- |
|
|
| |||
|
| [`E;M] Measurement Error |
|
| |||
| eter will display the cause of the input error. |
|
|
| |||
|
| [E;CAL] Bad Calibration Data |
|
| |||
|
|
|
|
|
|
| |
|
|
|
|
| [Er;Ab] Ambient Error |
|
|
|
|
|
|
| [E;Rtd] RTD Lead Resistance Error |
|
|
|
|
|
|
|
|
| |
[`i;Ca] | Analog Input (1 or 2) |
|
| 0.0 | always | ||
[ i.CA] | Calibration Offset |
|
|
|
| ||
| Offset the input reading to compensate for lead |
|
|
|
| ||
| wire resistance or other factors that cause the in- |
|
|
|
| ||
| put reading to vary from the actual process value. |
|
|
|
| ||
|
|
|
|
|
|
|
|
[`dio] |
| [```5] | [```6] |
|
|
|
|
[oPEr] |
| [`dio] | [`dio] |
|
|
| |
Digital Input/ | Digital Input or | Digital Input or |
|
|
| ||
Output Menu | Output 5 | Output 6 | (menu appears if PM6 _ [2 or 4] _ | ||||
|
|
|
|
|
|
| |
[`do;S] | Digital Output (5 or 6) |
|
| [``on] On |
| always | |
[ do.S] | Output State |
|
| [`off] Off |
|
| |
| View the state of this output. |
|
|
|
|
| |
|
|
|
|
|
|
| |
[`Ei;S] | Digital Input (5 or 6) |
|
| [iACt] Inactive |
| always | |
[ Ei.S] | Event Input Status |
|
| [`ACt] Active |
|
| |
| View this event input state. |
|
|
|
|
| |
|
|
|
|
|
|
|
|
[LiM] |
|
|
|
|
|
|
|
[oPEr] |
|
|
|
|
|
|
|
Limit Menu | (menu appears if PM6 _ _ _ |
|
|
| |||
|
|
|
|
|
|
|
|
[`LL;S] | Limit |
|
|
| 0.0°F or | Limit Sides (Set- | |
[ LL.S] | Low Set Point |
|
| units | up Page) is not | ||
| Set the low process value that will trigger the |
|
| set to High. | |||
| limit. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[`Lh;S] | Limit |
|
|
| 0.0°F or | Limit Sides (Set- | |
[ Lh.S] | High Set Point |
|
| units | up Page) is not | ||
| Set the high process value that will trigger the |
|
| set to Low. | |||
| limit. |
|
|
|
|
|
|
[Mon] |
|
|
|
|
|
|
|
[oPEr] |
|
|
|
|
|
|
|
Monitor Menu |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
[C;MA] | Monitor |
|
|
| [`off] Off |
| always |
[C.MA] | Control Mode Active |
|
| [AUto] Auto |
|
| |
| View the current control mode. |
|
| [MAn] Manual |
|
| |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
[`h;Pr] | Monitor |
|
|
| 0.0 to 100.0% | 0.0 | always |
[h.Pr] Heat Power
View the current heat output level.
[`C;Pr] Monitor | 0.0 | always |
[C.Pr] Cool Power
View the current cool output level.
[`C;SP] | Monitor | 75°F or | always | |
[ C.SP] | Closed Loop Working Set Point | units |
| |
| View the set point currently in effect. |
| 24°C |
|
|
|
|
|
|
[`Pu;A] | Monitor |
| always | |
[ Pv.A] | Process Value Active |
|
| |
| View the current filtered process value using the |
|
|
|
| control input. |
|
|
|
Note: Some values will be rounded off to fit in the
If there is only one instance of a menu, no submenus will appear.
Watlow | • 29 • | Chapter 5 Operations Page |