2-4
12345678296774425745542764696
This dryer is suitable for mobile home installations. The
i
nstallation must conform to the Manufactured Home
Construction and Safety Standard, T itle 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240
M
H.
123456782967455427646
Meta l exhaust system hardw are, which is available for
purchase from your dealer.
Specia l pr ov is ions m ust b e made in mob ile h om e s to
intr od uc e ou tside air into th e dryer. The open ing (such a s a
nearby window) should be at least twice as lar ge as the dryer
exhaust opening.
5645 64696 5
747276243454
To contact a qualified electrical inst aller.
To be sur e that the electrical connection is adequate a nd in
conformance with the National Electrical C ode, ANSI/NFPA
70 -la tes t editio n and a ll loca l cod es a nd ordina nces.
The Natio nal Electric Code requires a 4-wire power supply
co nn e ction for hom e s bu ilt after 1996 , drye r cir cu its invol ved
in remodeling after 1996, and all mobile home installations.
A copy of the above code standards can be obtained from:
Nat ional Fir e Prote ction Asso ciati on, One Batt erym arch Par k,
Quincy, MA 02269 .
To supply the requir ed 3 or 4 wire, single phase, 120/240 volt,
60 H z. , A C only ele ct rical su p ply (o r 3 or 4 wi re, 12 0/2 08 v ol t
elec trical supply, if sp ecified on the serial/rating plate) on a
separate 30-amp c ircuit, fused on both sides of the line. A
time-delay fuse or circuit breaker is recommended. Connect
to an individ ual branch circuit. Do not have a fuse in the
neu tra l or gr ou nd ing ci r cuit .
Do not use an extension cord.
If co des p er mit and a sepa r ate grou nd wire is used, it is
recommended that a qualified electrician determi ne that the
gr o un d path is ade q uat e.
564572642
T
o properly install you r dryer, you must determine the type of
electrical co nnection you will be using and follow the instructions
p
rovided for it here.
This dryer is manufa ctur ed ready to install with a 3-wire
elect rical suppl y conn ection. The neut ral gr ound co nduc tor is
permanently connected to the neutral conductor (white wire)
with in the dry er. If the dry er is installed with a 4-w ir e electrical
supply connection, the neutral ground conductor must be
remove d fro m the ex ternal gr ou n d con ne ct or (gr een sc re w ),
and secured under the neutral terminal (center or white wire)
of the ter mi nal block. When the neutra l ground conductor is
secured under the neutral t ermin al (center or white wire) of
the terminal block, the dryer cabinet is isolated from the
neu tr al conductor.
If local cod es do not per mi t the co nnec tion of a n eut ra l
ground wire to the neutr al wire, see ?Optional 3-wire
connection
?
section.
A 4-wire power supply connection must be us ed when the
appliance i s ins talle d in a location where groundin g through
th e neut ra l conductor is pr oh ibi te d. Gr ounding through t he
neutral is prohibited for (1) new branch-circuit installations,
(2) mobile homes, (3) recreational veh icles, and (4) areas
where local codes prohibit grounding through the neutral
conductors.
Use a UL listed power supply cord kit marked for use with
clot h es drye rs . T he kit sho ul d contain:
A UL listed 30-amp power supply cor d, rated 120/240 volt
minim um. The cor d should be type SRD or SRDT and be at
le a s t 4 ft (1.22 m) lon g. T he w ires that co nnect t o the drye r
mu st end in ring terminals or spade terminals with upturned
ends.
A UL listed strain relief.
Then choose a 4-wire power supp ly cor d with ring or spade
terminals and UL listed strain relief. The 4-wir e power supply
cord, at least 4 ft (1.22 m) long, must have four 10-gauge copper
wir e s and ma t ch a 4-w ire re ce p tac le of NE M A Type 14 -30R . The
ground wire (ground conductor) may be eithe r green or bare. The
neu tral conductor must be ident ified by a white cov er.
Then choose a 3-wire power supp ly cor d with ring or spade
terminals and UL listed strain relief. The 3-wir e power supply
co rd, at least 4 ft (1. 22 m) long, m ust have thr ee 10- gauge co pper
wir e s and match a 3-w ire r e ceptacle of NEM A Type 10-30 R.
Pow er sup pl y cabl e m u st ma tc h pow er su p ply (4- w ir e or 3-wi r e
)
and be:
Flexible armore d c able or nonmetallic sheathed copper cable
(wit h gro und wir e), prot ected w ith flexible me tallic co nduit. A
ll
current-carrying wires must be insulated.
10-gauge solid copper wire (do not use aluminu m).