Whirlpool MED / GD 9700S, MED / GD 9600S manual 369#8

1234567482 9￿￿￿3457￿￿ ￿ ￿￿￿￿￿￿ ￿￿2￿

￿￿￿36￿￿￿￿￿2￿￿9￿6￿

￿￿76345￿￿763

989￿6￿￿￿￿8￿￿9

69￿￿￿%#￿8￿'26￿99￿6￿￿￿!12345464￿989￿6￿￿￿￿8￿98￿2%￿&￿69￿￿"￿9#￿￿9￿￿￿￿￿87￿￿2￿￿#

989￿6￿￿￿￿8￿￿91￿#￿￿#99￿69￿%#￿8￿'26￿99￿6￿￿￿!￿￿￿￿9￿1234546￿98￿2￿￿92￿￿￿￿

)

!￿￿9

98969￿

6￿￿8￿9'6￿

￿￿￿2

)

%￿&￿69

"￿#69￿￿￿￿9'

6￿

￿￿￿2

9'￿￿￿6

!9

￿

￿￿9￿669￿6￿

￿9￿￿￿

!￿￿9

￿9'￿￿￿6!9

￿￿￿9￿6￿6￿

#￿99￿

#3￿￿87

$￿￿￿

#3￿9￿6

989￿6￿￿￿￿8￿￿￿#

87

￿9￿62

￿￿9￿6￿￿￿2

#59￿99￿￿876#&69￿￿88989￿6￿￿￿￿8￿￿￿￿9￿6￿￿￿2

$59￿￿￿￿

6#&69￿￿88

69

%￿8(9

￿9￿6&*￿￿￿9*￿9￿￿￿

69

%￿8(9

2

369

#￿￿8￿

1

369#￿￿8￿

￿9

￿&￿￿"2

￿9

￿&￿￿"2

￿9￿￿

￿￿￿￿9￿￿86

￿￿￿￿9￿￿86￿9￿6&*￿￿￿9*￿￿87 ￿9￿￿￿

			#￿￿51￿5￿￿￿￿"1￿￿7￿￿	91￿￿	6"
					￿￿1"5￿￿￿￿
Disconnect power.			￿3789￿￿185￿￿5!17958￿￿1"￿￿￿7￿￿￿1￿￿￿￿
Remove the hold-down screw and terminal block cover.
3	758	￿1758￿9￿￿1￿￿85￿	Put power supply cord through the strain relief. Be sure
123	758￿
			that the wire insulation on the power supply cord is inside
			the strain relief. The strain relief should have a tight fit with
			the dryer cabinet and be in a horizontal position. Do not
			further tighten strain relief screws at this point.

4256789￿1￿￿58￿￿￿9￿1￿￿￿￿￿￿87￿￿￿￿￿6Install strain relief. ￿1￿￿￿￿￿￿￿98￿9￿

Remove the screws from a /2" (1.9 cm) UL listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections into the hole below the terminal block opening so that one tab is pointing up and the other is pointing down, and hold in place. Tighten strain relief screws just enough to hold the two clamp sections together.

2-6