Graphical user interface (GUI) menu
Zone2 Initial Vol./Zone3 Initial Vol./Zone4 Initial Vol. (Zone 2/Zone 3/Zone 4 initial volume setting)
Use this feature to set the volume level of Zone 2, Zone 3, or Zone 4 when the power of each zone is turned on.
Control range: Off, Mute,
Control step: 0.5 dB
Note
The “Zone2 Max Vol.”, “Zone3 Max Vol.”, or “Zone4 Max Vol.” setting takes priority over the “Zone2 Initial Vol.”, “Zone3 Initial Vol.”, “Zone4 Initial Vol.” setting.
Zone2 Balance/Zone3 Balance/Zone4 Balance (Zone 2/Zone 3/Zone 4 balance)
Use this feature to adjust the balance of the volume of the left and right channels in each zone.
Choices: L10 to L1, 0, R1 to R10
Zone2 Mono/Zone3 Mono/Zone4 Mono (Zone 2/Zone 3/Zone 4 monaural mode)
Use this feature to select whether you play back sources monaurally in the selected zone.
Choice | Descriptions |
Off | Turns off the monaural playback mode. This unit plays |
| back sources in stereo. |
|
|
On | Turns on the monaural playback mode. This unit mixes |
| down the left and right channel signals and plays the |
| sources monaurally. |
|
|
Muting Type
(Zone 2/Zone 3/Zone 4 muting type)
Use this feature to adjust how much the mute function reduces the output volume of the selected zone.
Choice | Functions |
Full | Mutes all the audio output. |
|
|
Reduces the current volume by 20 dB. | |
|
|
Reduces the current volume by 40 dB. | |
|
|
■Zone OSD (Zone on-screen display)
Use this feature to display the operational status of Zone 2, Zone 3, and Zone 4 on the Zone 2 video monitor connected to the ZONE VIDEO jacks on the rear panel of this unit. The Zone 2, Zone 3, and Zone 4 information to be displayed is listed as follows:
•The input source
•The volume level
•The audio mute status
•The tonal quality status
•iPod or network/USB menu when “DOCK” or “NET/USB” is selected as the input source of Zone 2, Zone 3, and/or Zone 4
Choice | Functions |
Zone2 | Displays the operational status of Zone 2 only. |
|
|
Zone All | Displays the operational status of Zone 2, Zone 3, and |
| Zone 4. |
|
|
Notes
•You can connect up to two composite and one component video monitors to the ZONE OUT VIDEO jacks and ZONE OUT COMPONENT VIDEO jacks. If you connect multiple video monitors to the ZONE VIDEO and ZONE OUT COMPONENT VIDEO jacks, these video monitors display the same video images of the input source of Zone 2.
•When you set “Zone OSD” to “Zone All”, the operational status of Zone 3 and Zone 4 appears on the Zone 2 video monitor(s) even if Zone 2 is turned off.
Manual Setup (Network)
Use this menu to adjust the network and USB system parameters.
■Configuration (Network configuration)
Use this feature to view the network parameters (IP address, etc.) or to change them manually.
DHCP (DHCP setting)
Use this feature to select whether this unit can obtain the network parameters (IP address, subnet mask, default gateway, primary DNS server and secondary DNS server) from the DHCP server of the connected network.
Choice | Descriptions |
On | Select this setting when this unit can obtain the network |
| parameters from the DHCP server of the connected |
| network. |
|
|
Off | Select this setting when you set the network parameters |
| manually. |
|
|
IP Address (IP address)
Use this parameter to specify an IP address assigned to this unit. This value must not duplicate the one used for other devices in the target network.
Subnet Mask (Subnet mask)
Use this parameter to specify the subnet mask value assigned to this unit.
y
For most of the cases, the subnet mask value can be set as “255.255.255.0”.
Default Gateway (Default gateway)
Use this parameter to specify the IP address of the default gateway.
DNS Server (P) (Primary DNS server)
DNS Server (S) (Secondary DNS server)
Use this parameter to specify the IP address of the primary and secondary DNS (Domain Name System) servers.
Note
If you have only one DNS address, enter the DNS address in “DNS Server (P)”. If you have two or more DNS addresses, enter one of them in “DNS Server (P)” and another in “DNS Server (S)”.
Setup (Setup)
Select “Setup” to confirm the settings of the “Configuration” parameters.
Procedure of the network configuration
1From the top GUI menu, press 9k / n on the remote control repeatedly and then 9h to select “Configuration”.
2Press 9k / n repeatedly and then 9h to select “DHCP”.
