|
| Troubleshooting | |
During Auto Setup |
|
|
|
|
|
|
|
Error message | Cause | Remedy | See page |
E01:No Front SP | Front L/R channel signals are not detected. | Check the front L/R speaker connections. | 23 |
|
|
|
|
E02:No Sur. SP | A surround channel signal is not detected. | Check the surround speaker connections. | 23 |
|
|
|
|
E03:No F. PRNS SP | A front presence channel signal is not detected. | Check the front presence speaker connections. | 23 |
|
|
|
|
E04:SBR → SBL | Only right surround back channel signal is detected. | Connect the surround back speaker to the | 23 |
|
|
| |
|
| only have one surround back speaker. |
|
|
|
|
|
E05:Noisy | Background noise is too loud. | Try running “Auto Setup” in a quiet environment. | — |
|
|
|
|
|
| Turn off noisy electric equipment like air | — |
|
| conditioners or move them away from the optimizer |
|
|
| microphone. |
|
|
|
|
|
E06:Check Sur. | Surround back speakers are connected, though | Connect surround speakers when you use surround | 23 |
| surround L/R speakers are not. | back speakers. |
|
|
|
|
|
E07:No MIC | The optimizer microphone was unplugged during | Connect the supplied optimizer microphone to the | 43 |
| the “Auto Setup” procedure. | OPTIMIZER MIC jack on the front panel. |
|
|
|
|
|
E08:No R.PRNS SP | A rear presence channel signal is not detected. | Check the rear presence speaker connections. | 23 |
|
|
|
|
E09:User Cancel | The “Auto Setup” procedure was cancelled due to | Run “Auto Setup” again. | 42 |
| user activity. |
|
|
|
|
|
|
E10:Internal Err. | An internal error occurred. | Run “Auto Setup” again. | 42 |
|
|
|
|
After Auto Setup |
|
|
|
|
|
|
|
Warning message | Cause | Remedy | See page |
W1:Out of Phase | Speaker polarity is not correct. This message may | Check the speaker connections for proper polarity | 23 |
| appear depending on the speakers even when the | (+ or |
|
| speakers are connected correctly. |
|
|
|
|
|
|
W2:Over Distance | The distance between the speaker and the listening | Bring the speaker closer to the listening position. | — |
| position is over 24 m (80 ft). |
|
|
|
|
|
|
W3:Level Error | The difference of volume level among speakers is | Readjust the speaker installation so that all speakers | — |
| excessive. | are set in locations with similar conditions. |
|
|
|
|
|
|
| Check the speaker connections. | 23 |
|
|
|
|
|
| Use speakers of similar quality. | — |
|
|
|
|
|
| Adjust the output volume of the subwoofer. | 42 |
|
|
|
|
W4:SP Mismatch | The result of the wiring check of “Auto Setup” is | Use “Speaker Set” in “Manual Setup” to adjust the | 84 |
| different from “Speaker Set” in “Manual Setup”. | speaker settings manually. |
|
|
|
|
|
| “Wiring” check procedure is skipped. | Select “Wiring” in “Setup Menu”. | 44 |
|
|
|
|
Notes
•If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “Auto Setup” again.
•If warning “W2” or “W3” appears, the adjustment are made, however the adjustments may not be optimal.
•Depending on the speakers, warning “W1” may appears even if the speakers connections are correct.
•If error “E10” occurs repeatedly, please contact a qualified Yamaha service center.
Information | Additional |
|
|
■Resetting the system
Use this feature to reset all the parameters of this unit to the initial factory settings.
Notes
•This procedure completely resets all the parameters of this unit including the GUI menu parameters.
•The initial factory settings are activated next time you turn on this unit.
y
To cancel the initialization procedure at any time without making any changes, press BMASTER ON/OFF on the front panel to release it outward to the OFF position.
1Press BMASTER ON/OFF on the front panel to release it outward to the OFF position to turn off this unit.
2Press and hold IPROGRAM and then press
BMASTER ON/OFF inward to the ON position to turn on this unit.
Press and hold IPROGRAM until “ADVANCED SETUP” appears in the front panel display (see page 119).
3Rotate IPROGRAM to select “INITIALIZE”.
4Press IPROGRAM repeatedly to select “ALL”. y
•Select “CANCEL” to cancel the initialization procedure without making any changes.
•You can initialize the video parameters or sound field program parameters separately. See page 120 for details.
5Press BMASTER ON/OFF to release it outward to the OFF position to confirm your selection and turn off this unit.
