
1Press GSETUP on the remote control using a ballpoint pen or similar object.
The remote control enters the setup menu. “SETUP” appears in the display window (4) on the remote control.
2Press 9k / n repeatedly to select
The remote control enters the preset mode.
3Set the operation mode selector to GSOURCE and then press an input selector button or (3) or
5SELECT l / h repeatedly to select the control area you want to customize.
P-SET
DVD
y
Remote control features
Notes
•“ERROR” appears in the display window (4) on the remote control if you press a button not indicated in the respective step, or when you press more than one button simultaneously.
•The supplied remote control does not contain all possible codes for commercially available audio and video components (including Yamaha components). If operation is not possible with any of the remote control codes, program the new remote control function using the learning feature (see “Programming codes from other remote controls (LEARN)” on page 105) or use the remote control supplied with the component.
•Functions programmed using the learning mode take priority over remote control code functions.
•If you set “00012” as the remote control code of the selected control area, you can operate the currently selected internal source (DOCK, or NET/USB).
Programming codes from other remote controls (LEARN)
You can program remote control codes from other remote controls. Use the learning feature if you want to program functions not included in the basic operations covered by the remote control codes, or an appropriate remote control code is not available. You can program the function of other remote control to the buttons in the highlighted areas in the following illustration. The buttons can be programmed independently for each control area.
If you want to select “TV”, set the operation mode selector to FTV.
4Press 9ENTER.
The
04306
Note
“00000” appears in the display window (4) if no code has been set.
POWER POWER STANDBY POWER
TV AV
MULTI | PHONO | MD | ||
TAPE | ||||
|
|
| ||
BD | DVD | CD | ||
HD DVD | ||||
|
|
| ||
CBL | DTV | DVR | VCR | |
SAT | ||||
|
|
| ||
TUNER | DOCK | NET |
| |
USB |
| |||
|
|
| ||
|
|
| AMP | |
|
|
| TV | |
|
|
| SOURCE | |
SELECT | SETUP | ID MACRO |
|
Set to
SOURCE
| SYSTEM MEMORY |
| |
1 | 2 | 3 | 4 |
LEVEL | PRESET/CH | SRCH MODE | VOLUME |
TITLE | MENU |
| |
|
| ||
BAND |
|
|
|
| ENTER |
| |
|
|
| |
RETURN |
| DISPLAY |
|
MEMORY |
|
| MUTE |
|
|
| |
PC/MCX |
|
|
|
REC |
|
|
|
NET RADIO | USB |
|
|
CLASSICAL 1 | CLASSICAL 2 | LIVE/CLUB | ENTERTAIN |
1 | 2 | 3 | 4 |
MOVIE | STEREO | ENHANCER | SUR. DECODE |
5 | 6 | 7 | 8 |
THX | STRAIGHT | PURE DIRECT | EXTD SUR. |
9 | 0 | 10 | ENT |
PARTY | SLEEP | HDMI OUT | AUDIO SEL |
|
| MUTE | AUDIO |
TV VOL | TV CH | TV | 3D DSP |
|
| INPUT |
|
Operation | Advanced |
5Press the numeric buttons (B) to enter the
For a complete list of available remote control codes, refer to “List of remote control codes” at the end of this manual.
y
You can also enter the desired number by pressing 9 k / n / l / h repeatedly.
6Press 9ENTER to set the number.
“OK” appears in the display window (4) if setting was successful.
“NG” appears in the display window (4) if the setting was unsuccessful. In this case, start over from step 3.
y
If you continuously want to set up another code for another control area, repeat steps 3 through 6.
7Press GSETUP again to exit from the setup mode.
8Press Ap or 2AV POWER to confirm whether you can control your component using the remote control.
y
If operation is not possible and the manufacturer of your component has more than one code, try each of them until you find the correct one.
Notes
•The remote control transmits infrared rays. If the other remote control also uses infrared rays, this remote control can learn most of its functions. However, you may not be able to program some special signals or extremely long transmissions. Refer to the operating instructions for the other remote control.
•You cannot program the desired remote control code even if you select the buttons in the highlighted area in the above illustration depending on the selected control area and the assigned library.
1Set the operation mode selector to FSOURCE and then press an input selector button or (3) to select the desired control area.
The name of the control area you want to customize appears in the display window (4) on the remote control.
y
•You can also select the desired control area by pressing 5SELECT l / h repeatedly.
•If you want to select “TV”, set the operation mode selector to FTV.
Note
Make sure that the operation mode selector is set to FSOURCE or FTV. When you set the operation mode selector to FAMP and program a remote control codes from other remote controls, the programmed key cannot operate the amplifier function of this unit.
2Press GSETUP using a ballpoint pen or similar object.
“SETUP” appears in the display window (4).