Intel 5400 Series manual Overview, Test Preparation, Heatsink Preparation

Page 83

Heatsink Clip Load Methodology

CHeatsink Clip Load Methodology

C.1 Overview

This section describes a procedure for measuring the load applied by the heatsink/clip/ fastener assembly on a processor package.

This procedure is recommended to verify the preload is within the design target range for a design, and in different situations. For example:

•Heatsink preload for the LGA771 socket.

•Quantify preload degradation under bake conditions.

Note: This document reflects the current metrology used by Intel. Intel is continuously exploring new ways to improve metrology. Updates will be provided later as this document is revised as appropriate.

C.2 Test Preparation

C.2.1 Heatsink Preparation

Three load cells are assembled into the base of the heatsink under test, in the area interfacing with the processor Integrated Heat Spreader (IHS), using load cells equivalent to those listed in Section C.2.2.

To install the load cells, machine a pocket in the heatsink base, as shown in Figure C-1and Figure C-2. The load cells should be distributed evenly, as close as possible to the pocket walls. Apply wax around the circumference of each load cell and the surface of the pocket around each cell to maintain the load cells in place during the heatsink installation on the processor and motherboard.

The depth of the pocket depends on the height of the load cell used for the test. It is necessary that the load cells protrude out of the heatsink base. However, this protrusion should be kept minimal, as it will create an additional load offset since the heatsink base is artificially raised. The measurement load offset depends on the whole assembly stiffness (i.e. motherboard, clip, fastener, etc.). For example, the Quad-Core Intel® Xeon® Processor 5400 Series CEK Reference Heatsink Design clip and fasteners assembly have a stiffness of around 160 N/mm [915 lb/in]. If the resulting protrusion is 0.038 mm [0.0015”], then a extra load of 6.08 N [1.37 lb] will be created, and will need to be subtracted from the measured load. Figure C-3shows an example using the Quad-Core Intel® Xeon® Processor 5400 Series CEK Reference Heatsink designed for the Quad-Core Intel® Xeon® Processor 5400 Series in the 771–land LGA package.

Note: When optimizing the heatsink pocket depth, the variation of the load cell height should also be taken into account to make sure that all load cells protrude equally from the heatsink base. It may be useful to screen the load cells prior to installation to minimize variation.

Quad-Core Intel® Xeon® Processor 5400 Series TMDG

83

Page 82 Page 84
Image 83
Page 82 Page 84
Contents Thermal/Mechanical Design Guidelines Quad-Core Intel Xeon Processor 5400 SeriesQuad-Core Intel Xeon Processor 5400 Series Tmdg Contents Figures Preload Test Configuration Tables Initial release of the document Reference Revision Description Date NumberQuad-Core Intel Xeon Processor 5400 Series Tmdg References ObjectiveScope Term Description Definition of TermsTerms and Descriptions Sheet 1 TDP Terms and Descriptions Sheet 2Introduction Parameter Minimum Maximum Unit Mechanical RequirementsProcessor Mechanical Parameters Processor Mechanical Parameters TableQuad-Core Intel Xeon Processor 5400 Series Package Thermal/Mechanical Reference Design Thermal/Mechanical Reference Design Thermal/Mechanical Reference Design Quad-Core Intel Xeon Processor 5400 Series Considerations Thermal Control Circuit and TDP Processor Thermal Parameters and FeaturesDigital Thermal Sensor Multiple Digital Thermal Sensor Operation Platform Environmental Control Interface PeciMultiple Core Special Considerations Processor Input Processor Output Thermal Monitor for Multiple Core ProductsPROCHOT#, THERMTRIP#, and FORCEPR# Heatpipe Orientation for Multiple Core ProcessorsFeature Dimension Processor Core Geometric Center DimensionsEquation 2-1.y = ax + b Thermal ProfileEquation 2-2.TCONTROL= -TOFFSET Tcontrol DefinitionTcontrol and Thermal Profile Interaction Thermal Profile B Performance Targets Thermal/Mechanical Reference Design Thermal/Mechanical Reference Design 1U CEK, Thermal Profile B Parameter Maximum Unit2U+ CEK, Thermal Profile a 1U Alternative Heatsink Fan Fail GuidelinesSea-Level Fan Speed Control Characterizing Cooling Solution Performance RequirementsCondition FSC Scheme Processor Thermal Characterization Parameter RelationshipsFan Speed Control, Tcontrol and DTS Relationship Equation 2-3.ΨCA= Tcase TLA / TDPEquation 2-4.ΨCA= ΨCS + ΨSA ExampleEquation 2-6.ΨSA= ΨCA − ΨCS = 0.27 − 0.05 = 0.22 C/W Chassis Thermal Design ConsiderationsChassis Thermal Design Capabilities and Improvements Equation 2-5.ΨCA= Tcase TLA / TDP = 68 45 / 85 = 0.27 C/WHeatsink Design Considerations Heatsink SolutionsThermal/Mechanical Reference Design Considerations Summary Thermal Interface MaterialGeometric Envelope Assembly DrawingStructural Considerations of CEK 17 U+ CEK Heatsink Thermal Performance Thermal Solution Performance CharacteristicsEquation 2-8.y = 0.187*X + Thermal Profile AdherenceEquation 2-9.y = 0.246*X + =0.187* X +40Equation 2-10.y = 0.246*X + 1UCEKReference SolutionHeatsink with Captive Screws and Standoffs Components Overview22. Isometric View of the 2U+ CEK Heatsink Processor Minimum Maximum Units CEK Heatsink Thermal Mechanical CharacteristicsRecommended Thermal Grease Dispense Weight Thermal Interface Material TIM24. CEK Spring Isometric View CEK SpringThermal/Mechanical Reference Design Description Min Typ Max Unit Steady Startup Fan Power SupplyFan Specifications Boxed 4-wire PWM/DTS Heatsink Solution Systems Considerations Associated with the Active CEK Boxed Processor ContentsThermal/Mechanical Reference Design Figure A-1. Isometric View of the 1U Alternative Heatsink Component OverviewEquation A-1. y = 0.331*x + Thermal Solution Performance CharactericsThermal Profile Adherence = Processor power value W 1U Alternative Heatsink Thermal/Mechanical Design Drawing Description Table B-1. Mechanical Drawing ListFigure B-1 2U CEK Heatsink Sheet 1 Figure B-2 2U CEK Heatsink Sheet 2 Figure B-3 U CEK Heatsink Sheet 3 Figure B-4 2U CEK Heatsink Sheet 4 Figure B-5. CEK Spring Sheet 1 Figure B-6. CEK Spring Sheet 2 Figure B-7. CEK Spring Sheet 3 Mechanical Drawings Mechanical Drawings Mechanical Drawings Mechanical Drawings Mechanical Drawings Mechanical Drawings Figure B-14 U CEK Heatsink Sheet 1 Figure B-15 U CEK Heatsink Sheet 2 Figure B-16 U CEK Heatsink Sheet 3 Figure B-17 U CEK Heatsink Sheet 4 Figure B-18. Active CEK Thermal Solution Volumetric Sheet 1 Figure B-19. Active CEK Thermal Solution Volumetric Sheet 2 Figure B-20. Active CEK Thermal Solution Volumetric Sheet 3 Figure B-21 U Alternative Heatsink 1 Figure B-22 U Alternative Heatsink 2 Figure B-23 U Alternative Heatsink 3 Figure B-24 U Alternative Heatsink 4 Mechanical Drawings Heatsink Preparation OverviewTest Preparation Alternate Heatsink Sample Preparation Figure C-3. Preload Test Configuration Table C-1. Typical Test Equipment Test Procedure ExamplesTime-Zero, Room Temperature Preload Measurement Typical Test EquipmentPreload Degradation under Bake Conditions Heatsink Clip Load Methodology Safety Requirements Safety Requirements Reference Heatsink Thermal Verification Environmental Reliability TestingStructural Reliability Testing Intel Verification Criteria for the Reference DesignsTable E-1 Use Conditions Environment 2.2 Recommended Test SequencePost-Test Pass Criteria Material and Recycling Requirements Recommended BIOS/Processor/Memory Test ProceduresQuality and Reliability Requirements Supplier Information Intel Enabled SuppliersFor 1U Additional Suppliers2U Heatsink Alternative CEK Copper Fin Alternative CEK Copper Fin Enabled Suppliers Information 100 Quad-Core Intel Xeon Processor 5400 Series Tmdg
Top Page Image Contents