Spectrum Brands C6x VME64 Reset Conditions, VME A24 Slave Interface Reset, Jtag Reset, Sysreset

Page 17

Spectrum Signal Processing

Monaco Technical Reference

 

Introduction

1.6.Reset Conditions

The Monaco board responds to three types of reset conditions:

VME SYSRESET (VME bus /SYSRESET line)

VME A24 Slave Interface Reset (VME A24 Control Register bit D0)

JTAG reset (JTAG chain /TRST line)

The following table indicates which hardware components are reset by the specific reset condition.

Table 1 Reset Summary

 

Reset Condition (Y = Component is Reset)

 

 

 

 

Hardware

SYSRESET

Slave Interface Reset

JTAG Reset

 

 

 

 

Processor Nodes

Y

Y

 

 

 

 

 

SCV64 VME Interface chip

Y

 

 

 

 

 

 

HPI registers

Y

Y

 

 

 

 

 

Global Shared Bus registers

Y

Y

 

 

 

 

 

VME A24 slave interface registers

Y

Y

 

 

 

 

 

JTAG (within DSPs)

Y

Y

Y

 

 

 

 

PEM interface

Y

Y

 

 

 

 

 

PMC interface

Y

Y

 

 

 

 

 

DSP~LINK3 interface

Y

Y

 

 

 

 

 

1.6.1.VME SYSRESET

A VME SYSRESET is initiated when the /SYSRESET line on the VME bus is driven low. All devices and registers on the Monaco board are reset to their default conditions.

1.6.2.VME A24 Slave Interface Reset

The VME A24 slave interface reset is initiated from the VME bus by setting bit D0 of the VME A24 Control Register to “0”. All devices and registers on the Monaco board are reset to their default conditions except for the SCV64 VME interface chip. The VME A24 Control Register is located at VME A24 Base Address + 1004h. The base address for the VME A24 slave interface is set by jumper block JP1.

1.6.3.JTAG Reset

The JTAG path can be reset by asserting the /TRST line of the JTAG chain by an EMURST from the XDS or TBC. Only the JTAG path of the DSPs is reset by this action; no other devices or registers on the board are affected.

Part Number 500-00191

5

Revision 2.00

 

Image 17
Contents Monaco Revision Iii PrefaceHistory Document Rev Date ChangesChange Table of Contents Monaco Technical Reference Vii Viii List of Figures Table of Contents List of Tables Xii Product Operation Processors FeaturesIntroduction VME InterfacesPMC PEMReference Documents General Bus Architecture On-Board Power SupplyVME A24 Slave Interface Reset Reset ConditionsJtag Reset SysresetBoard Layout Board LayoutOUT Jumper settingsJumper Settings Description Part Number Processor Nodes Processor Configurations PopulatedProcessor Node Block Diagram External Memory Processor Memory ConfigurationInternal Memory 0x0180 DSP Memory Map Nodes B, C, and D AddressSynchronous Dram Synchronous Burst SramProcessor Expansion Module Host PortProcessor Boot Source Jumpers Node Processor BootingSerial Port Routing Serial Port RoutingVME and PMC Connections for Serial Port PEM Connections for Serial Port 0Global Shared Bus Global Shared Bus Access Source TargetMemory ArbitrationBurst Cycle Bus Access Single Cycle Bus AccessLocked Cycles Global Shared Bus SCV64 Primary Slave A32/A24 Interface VME64 Bus InterfaceVME Operation A24 Secondary Slave Interface AccessA24 Secondary Interface Memory Map Hpia HPI Register Addresses VME addressMaster A32/A24/A16 SCV64 Interface VME64 Bus Interface DSP~LINK3 Data Transfer Operating Modes DSP~LINK3 InterfaceAstrben Address Strobe Control ModeDSP~LINK3 Reset Interface SignalsDSP~LINK3 Interface PCI Offset Address Hurricane ConfigurationPCI Interface Value Initialize Hurricane Register SetBCC2A PCI Device Hurricane ImplementationJtag Chain Jtag DebuggingJtag Debugging Overview Interrupt HandlingInterrupt Routing DSP~LINK3 Interrupts to Node aPCI Bus Interrupts PEM InterruptsHurricane Interrupt SCV64 InterruptKIPL2 KIPL1 KIPL0 Kipl Status Bits and the Iack CycleBit Node Whose Access Caused the Bus Error Bus Error InterruptsVME Host Interrupts To Any Node Inter-processor InterruptsRegisters Register Address Summary Access Privilege BusKFC2..0 KSIZE1..0 KADDR1..0 Vpage RegisterVstatus Register KIPL2..0 BuserraKavec Vinta Register Vintb Register Vintc Register Vintd Register Kiplend Kipl Enable RegisterKiplenc KiplenbDSP~LINK3 Register DL3RESETID Register Hinta VME A24 Status RegisterHintb HintcVME A24 Control Register Registers Board Identification SpecificationsMonaco Monaco67General Specifications ParameterPerformance and Data Throughput Data Access/Transfer PerformanceSpecifications Connector Layout Connector PinoutsVME P1 Connector Pinout VME ConnectorsVME P2 Connector Pinout PMC to VME P2 VME P2 Connector DSP~LINK3 to VME P2 PMC Connector JN1 Pinout PMC ConnectorsPMC Connector JN2 PMC Connector JN4 Non-standard PMC Connector JN5 PEM 1 Connector Pinout PEM ConnectorsPEM 2 Connector Pinout Jtag OUT Connector Jtag ConnectorsJtag in Connector Pinout Connector Pinouts SCV64 Register Initialization Appendix a SCV64 Register ValuesSCV64 Register Initialization VME IndexInterrupts to node A, 40 register Reset Jtag Sysreset