Spectrum Brands C6x VME64 manual Vintc Register

Page 63

Spectrum Signal Processing	Monaco Technical Reference
	Registers

VINTC Register

Address: 016D 800Ch

D31..		..D8

Reserved

D7..	..D1	D0

Reserved		Interrupt

This register allows any processor to generate or clear an interrupt to node C. Upon reset this value is ‘0’.

∙To generate an interrupt to node C, set bit D0 of this register to “1”.

∙To clear an interrupt to node C, set bit D0 of this register to “0”.

Part Number 500-00191	51
Revision 2.00

Image 63

Contents Monaco Revision Iii PrefaceDocument Rev Date Changes ChangeHistory Table of Contents Monaco Technical Reference Vii Viii List of Figures Table of Contents List of Tables Xii Features IntroductionProduct Operation Processors PEM InterfacesVME PMCReference Documents General Bus Architecture On-Board Power SupplySysreset Reset ConditionsVME A24 Slave Interface Reset Jtag ResetBoard Layout Board LayoutJumper settings Jumper Settings DescriptionOUT Part Number Processor Nodes Processor Configurations PopulatedProcessor Node Block Diagram Processor Memory Configuration Internal MemoryExternal Memory 0x0180 DSP Memory Map Nodes B, C, and D AddressHost Port Synchronous Burst SramSynchronous Dram Processor Expansion ModuleProcessor Boot Source Jumpers Node Processor BootingSerial Port Routing Serial Port RoutingVME and PMC Connections for Serial Port PEM Connections for Serial Port 0Arbitration Global Shared Bus Access Source TargetGlobal Shared Bus MemoryBurst Cycle Bus Access Single Cycle Bus AccessLocked Cycles Global Shared Bus VME64 Bus Interface VME OperationSCV64 Primary Slave A32/A24 Interface A24 Secondary Slave Interface AccessA24 Secondary Interface Memory Map Hpia HPI Register Addresses VME addressMaster A32/A24/A16 SCV64 Interface VME64 Bus Interface DSP~LINK3 Data Transfer Operating Modes DSP~LINK3 InterfaceAstrben Address Strobe Control ModeDSP~LINK3 Reset Interface SignalsDSP~LINK3 Interface Hurricane Configuration PCI InterfacePCI Offset Address Value Initialize Hurricane Register SetBCC2A PCI Device Hurricane ImplementationJtag Chain Jtag DebuggingJtag Debugging Overview Interrupt HandlingInterrupt Routing DSP~LINK3 Interrupts to Node aSCV64 Interrupt PEM InterruptsPCI Bus Interrupts Hurricane InterruptKIPL2 KIPL1 KIPL0 Kipl Status Bits and the Iack CycleBit Node Whose Access Caused the Bus Error Bus Error InterruptsVME Host Interrupts To Any Node Inter-processor InterruptsRegisters Register Address Summary Access Privilege BusKFC2..0 KSIZE1..0 KADDR1..0 Vpage RegisterVstatus Register Buserra KavecKIPL2..0 Vinta Register Vintb Register Vintc Register Vintd Register Kiplenb Kipl Enable RegisterKiplend KiplencDSP~LINK3 Register DL3RESETID Register Hintc VME A24 Status RegisterHinta HintbVME A24 Control Register Registers Monaco67 SpecificationsBoard Identification MonacoGeneral Specifications ParameterPerformance and Data Throughput Data Access/Transfer PerformanceSpecifications Connector Layout Connector PinoutsVME P1 Connector Pinout VME ConnectorsVME P2 Connector Pinout PMC to VME P2 VME P2 Connector DSP~LINK3 to VME P2 PMC Connector JN1 Pinout PMC ConnectorsPMC Connector JN2 PMC Connector JN4 Non-standard PMC Connector JN5 PEM 1 Connector Pinout PEM ConnectorsPEM 2 Connector Pinout Jtag Connectors Jtag in Connector PinoutJtag OUT Connector Connector Pinouts SCV64 Register Initialization Appendix a SCV64 Register ValuesSCV64 Register Initialization VME IndexInterrupts to node A, 40 register Reset Jtag Sysreset