Orion Car Audio Power Connections for the XTR5001, XTR10001 and XTR15001, Speaker Connections

Page 11

Amplifier Wiring

Power Connections for the XTR5001, XTR10001 and XTR15001

•Power connections accept up to 4 AWG wire..

•4 AWG power and ground wire recommended for optimal per- formance..

•Connect 12V+ to the battery through fuse holder.. This connec- tion provides +12V main power to the amplifier..

•Power wire must be fused no more than 12” from battery..

•Ground amplifier to a good chassis ground as close as possible to the amplifier..

•Connect REM terminal to remote turn-on lead from source unit.. This connection provides +12V power to turn-on the amplifier..

•Add extra ground wire between the negative terminal of the battery and the chassis..

NOTE: The addition of a ground wire from the battery to the chassis of the vehicle improves the ability of the battery to supply power to the amplifier.. This is recommended because the current delivery of the factory electrical system was designed only to accommodate electron- ics supplied by the auto manufacturer..

Speaker Connections

The Orion XTR5001, XTR10001, and XTR15001 amplifiers offer two positive and two negative output terminals for ease of connecting the speakers to the amplifier.. Since these are mono amplifiers, the speaker connectors are paralleled internally.. Each amplifier is stable to 1Ω.. See following diagrams..

OUT

COPY MASTER

GAIN

Figure 9

Figura 9

Abbildung 9

© 2008 Directed Electronics. All rights reserved.

10

Image 11

Contents Amplifier Contents Introduction Infrasonic Subsonic Switch when On cuts off extremely low Low-Pass Frequency LPF Control adjusts the frequencyCEA Specifications Specifications Subsonic Filter Signal Input and Output ConfigurationsAdjusting Bass Boost Input GainSealed Example High-Pass Set at 20Hz Sealed Example High-Pass Set at 30Hz Phase SwitchesLine Output Configurations System Expansion Remote Gain Operation Internal Crossover ConfigurationsLow-Pass Crossover Speaker Connections Power Connections for the XTR5001, XTR10001 and XTR15001Master Amplifier Bridging strappingTrunk Compartment General Precautions and Installation TipsChoosing Mounting Locations Passenger CompartmentTools of the Trade Step By Step Installation Adjusting the Sound of the System Testing the SystemAmplifier Visual Troubleshooting Amplifier Top Plate Symptom Probable Cause Action To Take Troubleshooting TipsSymptom Probable Cause Directed Electronics. All rights reserved Disposition DES Panneaux Latéraux FrançaisCaractéristiques Techniques CEA Caractéristiques Techniques Réglage du renforcement des graves Configurations d’entrée et de sortie du signalRéglages DE L’AMPLIFICATEUR Gain d’entréeRéglage passe-haut à 30 Hz dans le cas d’un cais- son clos Commutateurs de phaseConfigurations de sortie ligne extension du sys- tème Réglage passe-haut à 20 Hz dans le cas d’un cais- son closFiltre passe-bas Configuration des filtres internesUtilisation de la télécommande du gain Pontage Raccordement DE L’AMPLIFICATEURRaccordement des haut-parleurs Habitacle Installation DE L’AMPLIFICATEURChoix des emplacements de montage Précautions générales et conseils d’installationOutillage requis Installation pas à pas Réglage du son du système Réglage ET Résolution DES ProblèmesEssai du système Résolution visuelle des problèmes de l’amplificateur Plaque supérieure de l’amplificateur Symptôme Cause probable Intervention Conseils de dépannageFrançais Symptôme Cause probable Disposiciones DEL Panel DE Extremo EspañolTHD+N Especificaciones DE LA CEAEspecificaciones Configuraciones DEL Amplificador Caja cerrada, pasaaltas en 30 Hz Configuraciones de salida de línea Expansión del sistemaConfiguraciones del crossover interno Caja sellada, pasaaltas en 20 HzControl de amplificación a distancia Crossover de pasabajasConexión en puente Cableado DEL AmplificadorConexiones de altavoces Maletero Instalación DEL AmplificadorSelección de ubicaciones de montaje Compartimiento de pasajerosHerramientas DEL Oficio Instalación paso a paso Prueba del sistema Configuración Y Detección Y Reparación DE AveríasDetección y reparación visual de averías del ampli- ficador Placa superior del amplificador Síntoma Causa probable Medidas a tomar Sugerencias de detección y reparación de averíasEspañol Síntoma Causa probable Layout DER Endplatten DeutschCEA-DATEN RGC2 Technische DatenSubsonic-Filter Signaleingangs- und -ausgangskonfigurationenVerstärkereinstellungen EingangsverstärkungLine-Ausgangskonfigurationen Systemerweiterung PhasenwahlschalterBeispiel Geschlossenes Gehäuse, Hochpassfilter bei 20 Hz Beispiel Geschlossenes Gehäuse, Hochpassfilter bei 30 HzBetrieb der Fernverstärkungsfunktion Interne Crossover-KonfigurationenTiefpass-Crossover Brückenmodus Koppelung VerstärkerverkabelungStromanschlüsse für den XTR5001, XTR10001 und XTR15001 LautsprecheranschlüsseFahrgastraum VerstärkerinstallationAllgemeine Vorsichts- und Installationshinweise Wahl der EinbaustelleWerkzeuge Schrittweise Installation Systemsound einstellen Einstellung UND ProblemlösungSystemtest Visuelle Anzeige von Problemen mit dem Verstärker Obere Platte des Verstärkers Symptom Mögliche Ursache Lösung ProblemlösungenLösung Symptom Mögliche UrsacheDirected Electronics. Alle Rechte vorbehalten Layout DEI Pannelli Terminali ItalianoSpecifiche CEA Dati Tecnici Filtro subsonico Configurazione dei segnali d’ingresso e di uscitaImpostazioni DELL’AMPLIFICATORE Guadagno d’ingressoSelettore della fase Configurazioni dell’uscita di linea espansione dell’impiantoComando del guadagno a distanza Configurazione dei crossover interniCrossover passa-basso Collegamento in parallelo Cablaggio DELL’AMPLIFICATOREConnessioni con gli altoparlanti Abitacolo Installazione DELL’AMPLIFICATOREScelta del punto di installazione Precauzioni generali e suggerimenti per l’installazioneCorredo per l’installazione Procedura di installazione Regolazione dell’audio dell’impianto Impostazione E Soluzione DEI ProblemiProva dell’impianto Spie dell’amplificatore Piastra superiore dell’amplificatore Sintomo Causa probabile Intervento necessario Soluzione dei problemiItaliano Sintomo Causa probabile Layouts DOS Painéis PortuguêsEspecificações DA CEA Especificações Ajuste da intensificação de graves Configurações de entrada e saída dos sinaisAjustes do Amplificador Ganho de entradaExemplo de caixa selada com passa-alta ajustado a 30Hz Configurações da saída de linha expansão do sistemaConfigurações do crossover interno Exemplo de caixa selada com passa-alta ajustado a 20 HzOperação de ganho remoto Crossover passa-baixaLigação em ponte interligação Conexão DOS Cabos do AmplificadorConexões elétricas do XTR5001, XTR10001 e XTR15001 Conexões dos alto-falantesPorta-malas Instalação do AmplificadorEscolha de locais de instalação Cabine de passageirosFerramentas Instalação passo a passo Como ajustar o som do sistema Ajuste E Resolução DE ProblemasComo testar o sistema Identificação visual de problemas com o amplifi- cador Placa superior do amplificador Problema Provável causa Medida a ser tomada Sugestões para resolução de problemasInterno deste manual Directed Electronics. Todos os direitos reservados 100 Warranty