Orion Car Audio XTR10001, XTR15001, XTR5001 Internal Crossover Configurations, Low-Pass Crossover

Page 10

Internal Crossover Configurations

The crossover section of the Orion XTR5001, XTR10001, and XTR15001 amplifiers is continuously variable and extremely flexible.. In addition to the variable built-in low-pass filters, the high-pass crossover incor- porates the Bass Boost feature.. This circuit is designed to optimize the performance of Orion subwoofers in all types of enclosures..

When using Orion loudspeakers, minor deviations from the recom- mended frequency ranges can provide superior results depending on your speaker locations and your vehicle acoustics.. Setting crossover frequencies higher than recommended will not cause damage and may provide superior sonic results depending on your system’s perfor- mance goals.. Refer to your loudspeaker owner’s manual for assistance in choosing the proper crossover frequencies for your system..

WARNING! DO NOT set crossover frequencies lower than the speakers recommended operating range.. This can cause driver failure that is not covered by the manufacturer’s warranty..

Low-Pass Crossover

When the switch is to the left (Full position), the low-pass crossover is bypassed.. When the switch is in the middle (12 position), the low-pass crossover is active with a 2nd order (12dB per octave) slope.. When the switch is to the right (24 position), the low-pass crossover is active with a 4th order (24dB per octave) slope.. The low-pass crossover is continu- ously variable from 30Hz to 250Hz..

Remote Gain Operation

NOTE: Do not use the Remote Gain control when you have an expanded system installed (see Line Output Configurations).. The Slave amplifier(s) gain will not be controlled..

The remote gain port provides easy remote access to the internal gain structure of the XTR power amplifier.. The RGC2 plugs into the amplifier via the 1/8” mini jack plug.. The RGC2 can be installed in the front of the vehicle to control the amplifier gain level.. The RGC2 can be used as a bass level control when used on an amplifier dedicated to subwoofers..

© 2008 Directed Electronics. All rights reserved.

9

Image 10

Contents Amplifier Contents Introduction Low-Pass Frequency LPF Control adjusts the frequency Infrasonic Subsonic Switch when On cuts off extremely lowCEA Specifications Specifications Input Gain Signal Input and Output ConfigurationsAdjusting Bass Boost Subsonic FilterSealed Example High-Pass Set at 20Hz Line Output Configurations System Expansion Phase SwitchesSealed Example High-Pass Set at 30Hz Low-Pass Crossover Internal Crossover ConfigurationsRemote Gain Operation Power Connections for the XTR5001, XTR10001 and XTR15001 Speaker ConnectionsBridging strapping Master AmplifierPassenger Compartment General Precautions and Installation TipsChoosing Mounting Locations Trunk CompartmentTools of the Trade Step By Step Installation Testing the System Adjusting the Sound of the SystemAmplifier Visual Troubleshooting Amplifier Top Plate Troubleshooting Tips Symptom Probable Cause Action To TakeSymptom Probable Cause Directed Electronics. All rights reserved Français Disposition DES Panneaux LatérauxCaractéristiques Techniques CEA Caractéristiques Techniques Gain d’entrée Configurations d’entrée et de sortie du signalRéglages DE L’AMPLIFICATEUR Réglage du renforcement des gravesRéglage passe-haut à 20 Hz dans le cas d’un cais- son clos Commutateurs de phaseConfigurations de sortie ligne extension du sys- tème Réglage passe-haut à 30 Hz dans le cas d’un cais- son closUtilisation de la télécommande du gain Configuration des filtres internesFiltre passe-bas Raccordement des haut-parleurs Raccordement DE L’AMPLIFICATEURPontage Précautions générales et conseils d’installation Installation DE L’AMPLIFICATEURChoix des emplacements de montage HabitacleOutillage requis Installation pas à pas Essai du système Réglage ET Résolution DES ProblèmesRéglage du son du système Résolution visuelle des problèmes de l’amplificateur Plaque supérieure de l’amplificateur Conseils de dépannage Symptôme Cause probable InterventionFrançais Symptôme Cause probable Español Disposiciones DEL Panel DE ExtremoEspecificaciones DE LA CEA THD+NEspecificaciones Configuraciones DEL Amplificador Caja sellada, pasaaltas en 20 Hz Configuraciones de salida de línea Expansión del sistemaConfiguraciones del crossover interno Caja cerrada, pasaaltas en 30 HzCrossover de pasabajas Control de amplificación a distanciaConexiones de altavoces Cableado DEL AmplificadorConexión en puente Compartimiento de pasajeros Instalación DEL AmplificadorSelección de ubicaciones de montaje MaleteroHerramientas DEL Oficio Instalación paso a paso Configuración Y Detección Y Reparación DE Averías Prueba del sistemaDetección y reparación visual de averías del ampli- ficador Placa superior del amplificador Sugerencias de detección y reparación de averías Síntoma Causa probable Medidas a tomarEspañol Síntoma Causa probable Deutsch Layout DER EndplattenCEA-DATEN Technische Daten RGC2Eingangsverstärkung Signaleingangs- und -ausgangskonfigurationenVerstärkereinstellungen Subsonic-FilterBeispiel Geschlossenes Gehäuse, Hochpassfilter bei 30 Hz PhasenwahlschalterBeispiel Geschlossenes Gehäuse, Hochpassfilter bei 20 Hz Line-Ausgangskonfigurationen SystemerweiterungTiefpass-Crossover Interne Crossover-KonfigurationenBetrieb der Fernverstärkungsfunktion Lautsprecheranschlüsse VerstärkerverkabelungStromanschlüsse für den XTR5001, XTR10001 und XTR15001 Brückenmodus KoppelungWahl der Einbaustelle VerstärkerinstallationAllgemeine Vorsichts- und Installationshinweise FahrgastraumWerkzeuge Schrittweise Installation Systemtest Einstellung UND ProblemlösungSystemsound einstellen Visuelle Anzeige von Problemen mit dem Verstärker Obere Platte des Verstärkers Problemlösungen Symptom Mögliche Ursache LösungSymptom Mögliche Ursache LösungDirected Electronics. Alle Rechte vorbehalten Italiano Layout DEI Pannelli TerminaliSpecifiche CEA Dati Tecnici Guadagno d’ingresso Configurazione dei segnali d’ingresso e di uscitaImpostazioni DELL’AMPLIFICATORE Filtro subsonicoConfigurazioni dell’uscita di linea espansione dell’impianto Selettore della faseCrossover passa-basso Configurazione dei crossover interniComando del guadagno a distanza Connessioni con gli altoparlanti Cablaggio DELL’AMPLIFICATORECollegamento in parallelo Precauzioni generali e suggerimenti per l’installazione Installazione DELL’AMPLIFICATOREScelta del punto di installazione AbitacoloCorredo per l’installazione Procedura di installazione Prova dell’impianto Impostazione E Soluzione DEI ProblemiRegolazione dell’audio dell’impianto Spie dell’amplificatore Piastra superiore dell’amplificatore Soluzione dei problemi Sintomo Causa probabile Intervento necessarioItaliano Sintomo Causa probabile Português Layouts DOS PainéisEspecificações DA CEA Especificações Ganho de entrada Configurações de entrada e saída dos sinaisAjustes do Amplificador Ajuste da intensificação de gravesExemplo de caixa selada com passa-alta ajustado a 20 Hz Configurações da saída de linha expansão do sistemaConfigurações do crossover interno Exemplo de caixa selada com passa-alta ajustado a 30HzCrossover passa-baixa Operação de ganho remotoConexões dos alto-falantes Conexão DOS Cabos do AmplificadorConexões elétricas do XTR5001, XTR10001 e XTR15001 Ligação em ponte interligaçãoCabine de passageiros Instalação do AmplificadorEscolha de locais de instalação Porta-malasFerramentas Instalação passo a passo Como testar o sistema Ajuste E Resolução DE ProblemasComo ajustar o som do sistema Identificação visual de problemas com o amplifi- cador Placa superior do amplificador Sugestões para resolução de problemas Problema Provável causa Medida a ser tomadaInterno deste manual Directed Electronics. Todos os direitos reservados 100 Warranty