Orion Car Audio XTR10001, XTR15001, XTR5001 Testing the System, Adjusting the Sound of the System

Page 16

Set Up and Troubleshooting

Testing the System

After you have completed the installation, you need to test the system.. This will help ensure years of trouble-free operation.. Please refer to the listed steps below when testing the sound of your Orion system..

1.Check all the wiring connections to be sure they are correct and secure..

2.Turn the signal source volume control all the way down.. Set any tone controls to their flat or defeated positions.. This includes the loudness control..

3.Turn the level controls of the amplifier to their minimum posi- tions..

4.Turn the source unit on.. Check to see if the power LED located on the connection side of the amplifier is on.. If not, please refer to the Power Connections and the Troubleshooting Tips sections of this manual for instructions..

5.If using an aftermarket source unit, turn the level controls of the amplifier about one quarter of a turn.. Slowly increase the volume level of the source unit to so that you can hear the output of the system.. If no sound is heard or if the output is distorted, turn the system off immediately.. Refer to the Power Connections and the Troubleshooting Tips sections of this manual to solve your instal- lation problems..

6.Check to make sure the output for each channel is correct.. If the active crossovers are used, check to make sure that each output is

correct from the amplifier.. When using active crossovers on mid- range and tweeters, do not use crossover frequencies lower than recommended.. If the system is not configured properly, refer to the Internal Crossover Configuration section of this manual and take corrective action..

7.If the output is clear and undistorted, continue to the Adjusting the Sound of the System section of this manual..

Adjusting the Sound of the System

Once you have checked the system’s operation, adjust the sound of the system.. Adjusting the sound of the system is accomplished by set- ting the level controls and adjusting the internal crossovers..

1.Turn the signal source volume control all the way down.. Set any tone controls to their flat or defeated positions.. This includes the loudness control..

2.Turn the level controls of the amplifier to their minimum posi- tions..

3.Choose music with high dynamic content that you like, with which you are familiar, and will be used most often in the system..

4.Turn the source unit’s volume control up to its highest undis- torted output level.. If you lack test equipment, this point occurs between 3/4 to full volume depending on the quality of your source unit.. Listen for any audible distortion.. If any distortion is audible, reduce the volume of the source unit until you have an undistorted output.. Leave the volume control at this position during your system tuning..

5.While listening to your chosen dynamic music, turn up the level control corresponding to the midrange output until you hear

© 2008 Directed Electronics. All rights reserved.

15

Image 16
Contents Amplifier Contents Introduction Low-Pass Frequency LPF Control adjusts the frequency Infrasonic Subsonic Switch when On cuts off extremely lowCEA Specifications Specifications Signal Input and Output Configurations Adjusting Bass BoostInput Gain Subsonic FilterSealed Example High-Pass Set at 20Hz Line Output Configurations System Expansion Phase SwitchesSealed Example High-Pass Set at 30Hz Low-Pass Crossover Internal Crossover ConfigurationsRemote Gain Operation Power Connections for the XTR5001, XTR10001 and XTR15001 Speaker ConnectionsBridging strapping Master AmplifierGeneral Precautions and Installation Tips Choosing Mounting LocationsPassenger Compartment Trunk CompartmentTools of the Trade Step By Step Installation Testing the System Adjusting the Sound of the SystemAmplifier Visual Troubleshooting Amplifier Top Plate Troubleshooting Tips Symptom Probable Cause Action To TakeSymptom Probable Cause Directed Electronics. All rights reserved Français Disposition DES Panneaux LatérauxCaractéristiques Techniques CEA Caractéristiques Techniques Configurations d’entrée et de sortie du signal Réglages DE L’AMPLIFICATEURGain d’entrée Réglage du renforcement des gravesCommutateurs de phase Configurations de sortie ligne extension du sys- tèmeRéglage passe-haut à 20 Hz dans le cas d’un cais- son clos Réglage passe-haut à 30 Hz dans le cas d’un cais- son closUtilisation de la télécommande du gain Configuration des filtres internesFiltre passe-bas Raccordement des haut-parleurs Raccordement DE L’AMPLIFICATEURPontage Installation DE L’AMPLIFICATEUR Choix des emplacements de montagePrécautions générales et conseils d’installation HabitacleOutillage requis Installation pas à pas Essai du système Réglage ET Résolution DES ProblèmesRéglage du son du système Résolution visuelle des problèmes de l’amplificateur Plaque supérieure de l’amplificateur Conseils de dépannage Symptôme Cause probable InterventionFrançais Symptôme Cause probable Español Disposiciones DEL Panel DE ExtremoEspecificaciones DE LA CEA THD+NEspecificaciones Configuraciones DEL Amplificador Configuraciones de salida de línea Expansión del sistema Configuraciones del crossover internoCaja sellada, pasaaltas en 20 Hz Caja cerrada, pasaaltas en 30 HzCrossover de pasabajas Control de amplificación a distanciaConexiones de altavoces Cableado DEL AmplificadorConexión en puente Instalación DEL Amplificador Selección de ubicaciones de montajeCompartimiento de pasajeros MaleteroHerramientas DEL Oficio Instalación paso a paso Configuración Y Detección Y Reparación DE Averías Prueba del sistemaDetección y reparación visual de averías del ampli- ficador Placa superior del amplificador Sugerencias de detección y reparación de averías Síntoma Causa probable Medidas a tomarEspañol Síntoma Causa probable Deutsch Layout DER EndplattenCEA-DATEN Technische Daten RGC2Signaleingangs- und -ausgangskonfigurationen VerstärkereinstellungenEingangsverstärkung Subsonic-FilterPhasenwahlschalter Beispiel Geschlossenes Gehäuse, Hochpassfilter bei 20 HzBeispiel Geschlossenes Gehäuse, Hochpassfilter bei 30 Hz Line-Ausgangskonfigurationen SystemerweiterungTiefpass-Crossover Interne Crossover-KonfigurationenBetrieb der Fernverstärkungsfunktion Verstärkerverkabelung Stromanschlüsse für den XTR5001, XTR10001 und XTR15001Lautsprecheranschlüsse Brückenmodus KoppelungVerstärkerinstallation Allgemeine Vorsichts- und InstallationshinweiseWahl der Einbaustelle FahrgastraumWerkzeuge Schrittweise Installation Systemtest Einstellung UND ProblemlösungSystemsound einstellen Visuelle Anzeige von Problemen mit dem Verstärker Obere Platte des Verstärkers Problemlösungen Symptom Mögliche Ursache LösungSymptom Mögliche Ursache LösungDirected Electronics. Alle Rechte vorbehalten Italiano Layout DEI Pannelli TerminaliSpecifiche CEA Dati Tecnici Configurazione dei segnali d’ingresso e di uscita Impostazioni DELL’AMPLIFICATOREGuadagno d’ingresso Filtro subsonicoConfigurazioni dell’uscita di linea espansione dell’impianto Selettore della faseCrossover passa-basso Configurazione dei crossover interniComando del guadagno a distanza Connessioni con gli altoparlanti Cablaggio DELL’AMPLIFICATORECollegamento in parallelo Installazione DELL’AMPLIFICATORE Scelta del punto di installazionePrecauzioni generali e suggerimenti per l’installazione AbitacoloCorredo per l’installazione Procedura di installazione Prova dell’impianto Impostazione E Soluzione DEI ProblemiRegolazione dell’audio dell’impianto Spie dell’amplificatore Piastra superiore dell’amplificatore Soluzione dei problemi Sintomo Causa probabile Intervento necessarioItaliano Sintomo Causa probabile Português Layouts DOS PainéisEspecificações DA CEA Especificações Configurações de entrada e saída dos sinais Ajustes do AmplificadorGanho de entrada Ajuste da intensificação de gravesConfigurações da saída de linha expansão do sistema Configurações do crossover internoExemplo de caixa selada com passa-alta ajustado a 20 Hz Exemplo de caixa selada com passa-alta ajustado a 30HzCrossover passa-baixa Operação de ganho remotoConexão DOS Cabos do Amplificador Conexões elétricas do XTR5001, XTR10001 e XTR15001Conexões dos alto-falantes Ligação em ponte interligaçãoInstalação do Amplificador Escolha de locais de instalaçãoCabine de passageiros Porta-malasFerramentas Instalação passo a passo Como testar o sistema Ajuste E Resolução DE ProblemasComo ajustar o som do sistema Identificação visual de problemas com o amplifi- cador Placa superior do amplificador Sugestões para resolução de problemas Problema Provável causa Medida a ser tomadaInterno deste manual Directed Electronics. Todos os direitos reservados 100 Warranty