Orion Car Audio XTR10001, XTR15001 Troubleshooting Tips, Symptom Probable Cause Action To Take

Page 19

Troubleshooting Tips

Symptom	Probable Cause	Action To Take

No output

	Low or no remote turn-on	Check remote turn-on voltage at voltage amplifier and repair as needed..

	Fuse blown	Check power wire's integrity and check for speaker shorts.. Fix as needed
		and replace fuse..

	Power wires not connected	Check power wire and ground connections and repair or replace as needed..

	Audio input not connected..	Check RCA connections and repair or replace as needed..

	Speaker wires not connected	Check speaker wires and repair or replace as needed..

	Speaker are blown	Check system with known working speaker and repair or replace speakers as
		needed..

Audio cycles on and off

	Thermal protection engages when amplifier heat	Make sure there is proper ventilation for amplifier and improve ventilation
	sink temperature exceeds 90º C (190º F)	as needed..

	Loose or poor audio input	Check RCA connections and repair or replace as needed..

	Loose power connections	Check power wires and ground connections and repair or replace as needed..

Distorted output

	Amplifier level sensitivity set too high exceeding	Readjust gain.. Refer to the Adjusting the Sound of the System section of this
	maximum capability of amplifier	manual for detailed instructions..

	Impedance load to amplifier too low	Check speaker impedance load, if below 1Ω, rewire the speakers to achieve
		higher impedance.
	Shorted speaker wires	Check speaker wires and repair or replace as needed..

© 2008 Directed Electronics. All rights reserved.

18

Image 19

Contents Amplifier Contents Introduction Infrasonic Subsonic Switch when On cuts off extremely low Low-Pass Frequency LPF Control adjusts the frequencyCEA Specifications Specifications Subsonic Filter Signal Input and Output ConfigurationsAdjusting Bass Boost Input GainSealed Example High-Pass Set at 20Hz Line Output Configurations System Expansion Phase SwitchesSealed Example High-Pass Set at 30Hz Low-Pass Crossover Internal Crossover ConfigurationsRemote Gain Operation Speaker Connections Power Connections for the XTR5001, XTR10001 and XTR15001Master Amplifier Bridging strappingTrunk Compartment General Precautions and Installation TipsChoosing Mounting Locations Passenger CompartmentTools of the Trade Step By Step Installation Adjusting the Sound of the System Testing the SystemAmplifier Visual Troubleshooting Amplifier Top Plate Symptom Probable Cause Action To Take Troubleshooting TipsSymptom Probable Cause Directed Electronics. All rights reserved Disposition DES Panneaux Latéraux FrançaisCaractéristiques Techniques CEA Caractéristiques Techniques Réglage du renforcement des graves Configurations d’entrée et de sortie du signalRéglages DE L’AMPLIFICATEUR Gain d’entréeRéglage passe-haut à 30 Hz dans le cas d’un cais- son clos Commutateurs de phaseConfigurations de sortie ligne extension du sys- tème Réglage passe-haut à 20 Hz dans le cas d’un cais- son closUtilisation de la télécommande du gain Configuration des filtres internesFiltre passe-bas Raccordement des haut-parleurs Raccordement DE L’AMPLIFICATEURPontage Habitacle Installation DE L’AMPLIFICATEURChoix des emplacements de montage Précautions générales et conseils d’installationOutillage requis Installation pas à pas Essai du système Réglage ET Résolution DES ProblèmesRéglage du son du système Résolution visuelle des problèmes de l’amplificateur Plaque supérieure de l’amplificateur Symptôme Cause probable Intervention Conseils de dépannageFrançais Symptôme Cause probable Disposiciones DEL Panel DE Extremo EspañolTHD+N Especificaciones DE LA CEAEspecificaciones Configuraciones DEL Amplificador Caja cerrada, pasaaltas en 30 Hz Configuraciones de salida de línea Expansión del sistemaConfiguraciones del crossover interno Caja sellada, pasaaltas en 20 HzControl de amplificación a distancia Crossover de pasabajasConexiones de altavoces Cableado DEL AmplificadorConexión en puente Maletero Instalación DEL AmplificadorSelección de ubicaciones de montaje Compartimiento de pasajerosHerramientas DEL Oficio Instalación paso a paso Prueba del sistema Configuración Y Detección Y Reparación DE AveríasDetección y reparación visual de averías del ampli- ficador Placa superior del amplificador Síntoma Causa probable Medidas a tomar Sugerencias de detección y reparación de averíasEspañol Síntoma Causa probable Layout DER Endplatten DeutschCEA-DATEN RGC2 Technische DatenSubsonic-Filter Signaleingangs- und -ausgangskonfigurationenVerstärkereinstellungen EingangsverstärkungLine-Ausgangskonfigurationen Systemerweiterung PhasenwahlschalterBeispiel Geschlossenes Gehäuse, Hochpassfilter bei 20 Hz Beispiel Geschlossenes Gehäuse, Hochpassfilter bei 30 HzTiefpass-Crossover Interne Crossover-KonfigurationenBetrieb der Fernverstärkungsfunktion Brückenmodus Koppelung VerstärkerverkabelungStromanschlüsse für den XTR5001, XTR10001 und XTR15001 LautsprecheranschlüsseFahrgastraum VerstärkerinstallationAllgemeine Vorsichts- und Installationshinweise Wahl der EinbaustelleWerkzeuge Schrittweise Installation Systemtest Einstellung UND ProblemlösungSystemsound einstellen Visuelle Anzeige von Problemen mit dem Verstärker Obere Platte des Verstärkers Symptom Mögliche Ursache Lösung ProblemlösungenLösung Symptom Mögliche UrsacheDirected Electronics. Alle Rechte vorbehalten Layout DEI Pannelli Terminali ItalianoSpecifiche CEA Dati Tecnici Filtro subsonico Configurazione dei segnali d’ingresso e di uscitaImpostazioni DELL’AMPLIFICATORE Guadagno d’ingressoSelettore della fase Configurazioni dell’uscita di linea espansione dell’impiantoCrossover passa-basso Configurazione dei crossover interniComando del guadagno a distanza Connessioni con gli altoparlanti Cablaggio DELL’AMPLIFICATORECollegamento in parallelo Abitacolo Installazione DELL’AMPLIFICATOREScelta del punto di installazione Precauzioni generali e suggerimenti per l’installazioneCorredo per l’installazione Procedura di installazione Prova dell’impianto Impostazione E Soluzione DEI ProblemiRegolazione dell’audio dell’impianto Spie dell’amplificatore Piastra superiore dell’amplificatore Sintomo Causa probabile Intervento necessario Soluzione dei problemiItaliano Sintomo Causa probabile Layouts DOS Painéis PortuguêsEspecificações DA CEA Especificações Ajuste da intensificação de graves Configurações de entrada e saída dos sinaisAjustes do Amplificador Ganho de entradaExemplo de caixa selada com passa-alta ajustado a 30Hz Configurações da saída de linha expansão do sistemaConfigurações do crossover interno Exemplo de caixa selada com passa-alta ajustado a 20 HzOperação de ganho remoto Crossover passa-baixaLigação em ponte interligação Conexão DOS Cabos do AmplificadorConexões elétricas do XTR5001, XTR10001 e XTR15001 Conexões dos alto-falantesPorta-malas Instalação do AmplificadorEscolha de locais de instalação Cabine de passageirosFerramentas Instalação passo a passo Como testar o sistema Ajuste E Resolução DE ProblemasComo ajustar o som do sistema Identificação visual de problemas com o amplifi- cador Placa superior do amplificador Problema Provável causa Medida a ser tomada Sugestões para resolução de problemasInterno deste manual Directed Electronics. Todos os direitos reservados 100 Warranty