Xantrex Technology 1800i, 1000i owner manual Control Panel, Prosine Powersave Mode

Page 14

3.3 Control Panel

WARNING

Review the Important Safety Instructions found at the beginning of this guide before operating the Prosine Inverter.

Once the Xantrex Prosine Inverter is properly installed and connected to batteries, it is ready to begin delivering AC power to your loads. The control panel is the interface between you and the inverter. This section describes the features of this panel and is followed by other sections that contain inverter operating information.

Figure 7. Control Panel

1.INVERTER #/I: this switch turns the Prosine Inverter either ON (I) or to BYPASS-state (#). It is also used to enable or disable POWERSAVE mode

during the power-up sequence. When in the (#) position, models equipped with a transfer relay will be

in the BYPASS mode, where incoming AC power is passed through to the load. The switch controls the output of the inverter with models equipped with AC outlets and does not control the output on hardwire units equipped with the transfer relay option.

2.LIQUID CRYSTAL DISPLAY (LCD): displays input current from the battery and battery voltage numerically. A multi-segment bar graph displays actual output power in watts from the inverter when a load is being operated.

3.MULTI-POSITION MOUNT: the control panel is designed so it can be removed and re-attached to the chassis in 90° increments depending on the mounting orientation of the inverter itself. The panel can also be removed entirely from the unit and mounted remotely, with the purchase of the optional Interface Panel.

4.FAULT CONDITION DISPLAY: should a fault occur, the error will immediately be displayed. An audible alarm sounds and the back-lighting of the display will flash to draw attention to the fault condition (see Section 5.1).

To operate the Prosine Inverter:

1.Turn the unit ON by moving the rocker switch on the control panel to (I) position. The following information will be displayed (upon each power-up), identifying the type and configuration of your Prosine Inverter:

•Model number (1000 or 1800 watt)

•Input Voltage, Output Voltage and Frequency configuration

•POWERSAVE mode OFF (factory set default)

Following the display of this information, the control panel then defaults to the standard display information of input voltage, input current and output power. When a load is connected, the output power (watts) is displayed in bar-graph form.

Figure 8. Control Panel Screen Sequence

Once the standard display screen is shown, the Prosine Inverter is ready to deliver AC power to your loads. You can now plug in a load to the front outlet of the unit, or, for those hardwire versions, into an outlet connected to the AC output of the inverter. The loads should operate from the inverter as they would from utility power. Section 3.5 explains the operating limits for the Prosine Inverter.

3.4 Prosine POWERSAVE Mode

Your Xantrex Prosine Inverter has a function mode called POWERSAVE. This “sleep” mode shuts off much of the power control circuitry of the inverter as well as the display back-lighting, reducing the stand- by current draw considerably. With this mode enabled, the unit draws approx. 1.5 W while powered up but with no load on the inverter. The Prosine Inverter detects the presence of a load by sending out pulses approximately once every 2.5 seconds. Full output power is available with the detection of a load. The unit will remain in POWERSAVE mode if the load it detects is less than 10 W for the 1000 model and less than 20 W for the 1800 model. This is a factory set search mode setting and cannot be changed.

You would want to enable POWERSAVE mode if the inverter is only being used periodically to power loads. This allows the inverter to draw less power from the batteries during non-use periods. If the inverter is being used frequently and your batteries are being recharged during inverter use (e.g. vehicle alternator), or soon after inverter use, you can leave POWERSAVE disabled.

Your inverter is factory default set to POWERSAVE OFF. To enable the POWERSAVE mode, follow these steps:

1.Turn the Control Panel switch to (#) position

2.Switch the unit back to (I) position. You will see the power-up information sequence being displayed as described previously.

3.When the Control Panel displays “POWERSAVE OFF” turn the switch to (#) position, wait for

10 English

Xantrex Prosine Inverter Owner’s Manual

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 1000 1000i 1800 1800i Page Table of Contents Date and Revision TrademarksExclusion for Documentation Part NumberExplosive Gas Precautions Important Safety InstructionsGeneral Safety Precautions Precautions When Working With BatteriesEnglish Introduction Prosine Inverter Key FeaturesAutomatic Transfer Switch Inverter FunctionLocating the Prosine Inverter InstallationRequirements for Installation Mounting the Prosine InverterFor units equipped with an AC outlet Wiring the Prosine InverterFor AC hardwire versions Input and Output ProtectionMaking AC Wiring Connections ModelGround Fault Circuit Interrupters GFCIs Making DC Wiring ConnectionsBattery Connections Output Waveform Prosine Inverter OperationPrinciples of Operation DC GroundingProsine Powersave Mode Control PanelTesting Inverter Operating Limits and Protection FeaturesTroubleshooting Guide Fault Conditions and IndicatorsWarranty and Return Information WarrantyBattery Type AppendicesBattery Size Power Derating Curve Performance GraphsEfficiency Curve Specifications Regulatory ApprovalsEnglish English Table des matières FrançaisManuel d’instruction du convertisseur Prosine Précautions contre les explosions de gaz Consignes de sécurité importantesPrécautions générales de sécurité Précautions à prendre avec des batteriesPanneau de contrôle Caractéristiques du convertisseur ProsineFonctionnement Basculement automatique optionMontage du convertisseur Exigences pour l’installationOù placer le convertisseur Prosine? Pour monter le convertisseurPour les versions bornier à vis Branchement du convertisseurPour les versions avec prise Protection en entrée et sortieBranchement en alternatif AC Pour connecter l’alternatifFabricant Numéro du Modèle Interrupteurs de Circuit pour panne liée La terre GFCIsBranchement du courant continu Pour connecter le continu Bateaux Véhicules de Maison Loisirs ModéleSortie sinusoïdale Fonctionnement du convertisseur ProsinePrincipes de fonctionnement Panneau de contrôleFonction Powersave Pour faire fonctionner le convertisseur ProsineModéle Fabricant et Modéle TestPour tester le convertisseur Guide de dépannage Défauts et indicateursGarantie Informations concernant la garantie et le retourPolitique d’autorisation de retour Annexe Type de batterieSeaGel Taille de la batterieDelco Voyager Graphiques des performances Courbe de perte de puissance en fonction de la températureCourbe de rendement 10. Spécifications et performances Conformité aux règlesFrançais Índice EspañolManuel del Usuario del Inversor Prosine Precauciones para Explosiones de Gas Instrucciones Importantes de SeguridadPrecauciones Generales de Seguridad Precauciones cuando trabaje con BateríasFunción del Inversor IntroducciónCaracterísticas principales del Inversor Prosine Tablero de ControlUbicando su Inversor Prosine InstalaciónRequisitos para la Instalación Montaje del Inversor ProsinePara las unidades equipadas con un tomacorrientes de CA Cable del Inversor ProsineComo montar el Inversor Prosine Para las versiones de cableado permanente de CAEl cable de CA debe de ser conectado en el siguiente orden Protección de Entrada y de SalidaHaciendo las Conexiones del Cable de Para hacer las conexiones del cable de CAInterruptor de Tierra del Circuito Defectuoso Gfci Fabricante Número de ModeloPara conectar los cables de CC AWGForma de Onda de Salida Funcionamiento del Inversor ProsinePrincipios sobre el Funcionamiento Conexión a Tierra de CCTablero de Control Figura 7. Tablero de Control del Inversor ProsineModalidad Powersave del Prosine Limites de Funcionamiento y Características de ProtecciónModelo Fabricante y número de ProbandoPara probar el Inversor Prosine Condiciones de falla e indicadores Guía de verificación y corrección de problemasProblema y síntomas Posible Cause Solución Información de garantía y devolución GarantíaApéndices Tipo de BateríaTamaño de la Batería West Marine Sea Volt Motomaster NautiliusGráficos de Performance Curva de Reducción de PotenciaCurva de Eficiencia Designaciones Especificaciones de PerformanceAprobaciones Regulatorias otras Inhaltsverzeichnis Deutsch Vorsichtsmaßnahmen bei explosiven Gasen Wichtige SicherheitshinweiseAllgemeine Sicherheitsmaßnahmen Vorsichtsmaßnahmen beim Arbeiten mit BatterienWechselrichterfunktion EinleitungHauptmerkmale des Prosine Wechselrichters BedienfeldAutomatischer Übertragungsschalter EinbauEinbauvoraussetzungen Vorgehensweise Einbauort des Prosine- WechselrichtersMontage des Prosine Bei festverdrahteten Modellversionen Verdrahtung des Prosine- WechselrichtersBei Geräten mit einem Wechselstromausgang Eingabe- und AusgabeschutzHerstellen der Wechselstrom- verdrahtung Hersteller Modell Nr Erdschluß-LeistungstrennerHerstellen der Gleichstrom- Drahtverbindungen Modell GebäudenHerstellen der Gleichstrom-Drahtverbindungen Gleichstrom-ErdungWellenform der Wechselstromausgabe Prosine-WechselrichterbetriebFunktionsweise BedienfeldDer ENERGIESPAR-Modus des Prosine Zum Betrieb des Prosine-WechselrichtersBetriebsgrenzwerte und Schutzvorrichtungen des Prosine Modell Hersteller und Modell NrStörungsursachen und Fehlermeldungen ÜberprüfungFehlersuche Überprüfen des Prosine-WechselrichtersGewährleistung und Rücksendeinformationen GewährleistungAnhang BatterieartenBatteriegröße Leistungsverlustkurve Wirkungsgradkurve Tips bei der Fehlersuche High Batt Shutdown =Und andere Bezeichnungen Technische DatenBehördliche Genehmigungen Anmerkungen 445-0049-01-01
Related manuals
Manual 2 pages 17.35 Kb Manual 66 pages 3.22 Kb Manual 70 pages 43.18 Kb

1800i, 1000, 1800, 1000i specifications

Xantrex Technology offers a range of power inverters that cater to both recreational and professional needs, with the Xantrex 1800 and 1000 models being among the most popular in their lineup. These inverters are specially designed to convert DC power from batteries into clean, pure sine wave AC power, making them suitable for running sensitive electronic devices and appliances.

The Xantrex 1800 is a robust inverter that delivers 1800 watts of continuous power and 3600 watts of peak power. This makes it ideal for powering essential appliances like refrigerators, microwaves, and power tools. Its compact design allows for easier installation in various settings such as RVs, boats, and off-grid homes.

On the other hand, the Xantrex 1000 inverter is designed for lower power requirements, offering 1000 watts of continuous power and 2000 watts of peak power. It is perfect for powering small appliances, electronics, and gadgets, making it a great choice for weekend campers and those who require less energy capacity.

Both models feature advanced technologies, including low idle power draw, which ensures that energy is conserved when the inverter is not actively powering devices. They also include overload protection, ensuring the inverter shuts down automatically if the power exceeds its limits, thus preventing damage to the unit or connected devices.

Another hallmark of Xantrex inverters is their user-friendly interface. The LED indicator lights provide clear status updates on the power output and inverter operation, making it easy for users to monitor performance at a glance. Additionally, both models feature various safety protocols, including short circuit and over-temperature protection, to enhance operational safety.

Installation is straightforward, thanks to the provided mounting options and wiring accessories. The units are designed to withstand harsh environments, with durable casings that enhance longevity and resilience.

In summary, the Xantrex 1800 and 1000 models offer reliable power solutions for a variety of applications. Their combination of high-quality sine wave output, advanced safety features, and user-friendly operation makes them a top choice for anyone seeking dependable off-grid power. With Xantrex, users can trust that they are investing in products engineered for performance and durability in an ever-increasing range of power needs.
Top Page Image Contents