Briggs & Stratton 074002 Inspect Safety Valve, Inspect Engine Oil Level, Oil Recommendations

Page 16

MAINTENANCE

Inspect Safety Valve

1.Pull ring on Safety Valve (see Figure 14) and ensure that Safety Valve operates freely.

Figure 14 - Safety Valve

Safety Valve Ring

2.If valve is stuck or does not operate smoothly, it must be replaced with same type of valve.Take unit to authorized service facility for repair.

Inspect Quick Connect Fittings and Tank Drain Valves

1.Turn engine ON/OFF switch to OFF position (see Figure 9 earlier).

2.Move Fuel Shutoff Valve lever to OFF position (see Figure 8 earlier).

WARNING

Compressed air stream from hose or tank drain can cause soft tissue damage to exposed skin and can propel objects leading to severe injury

and / or property damage.

•DO NOT direct air stream at self or others.

•Always wear ANSI Z87.1 approved safety glasses with side shields.

3.Disconnect air hose(s), air tool(s), or accessory from unit.Inspect Quick Connect fittings for damage and clean.

4.Pull ring on Safety Valve to reduce air pressure. Release Safety Valve ring.

5.Open Drain Valves (turn fully counterclockwise,

see Figure 2, earlier) and discharge accumulated water. Valves should operate smoothly and have full range of operation.

6.After water has drained, close Drain Valves fully clockwise.

NOTE: If Drain Valves are plugged, pull Safety Valve ring to fully drain air from tanks. Remove, clean and reinstall Drain Valves using pipe thread sealant.

Inspect Engine Oil Level

Oil Recommendations

NOTE: When adding oil to the engine crankcase, use only high quality detergent oil rated with API service classification SF, SG, SH, SJ or higher. DO NOT use special additives.

1.Choose a viscosity according to the table below:

 

 

 

 

 

 

 

 

 

 

 

 

30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5W-30, 10W-30

 

 

 

 

 

 

 

 

 

 

 

Synthetic

5W-30, 10W-30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

°F

-20

0

20

32 40

 

60

80

100

°C

-30

 

-20

-10

 

 

0

 

10

20

30

40

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

*The use of multi-viscosity oils (5W-30, 10W-30, etc.) in temperatures above 40°F (4°C) will result in higher than normal oil consumption. Inspect oil level more often when using a multi-viscosity oil.

**The use of SAE 30 oil in temperatures below 40°F (4°C) will result in hard starting and possible engine bore damage due to inadequate lubrication.

NOTE: Synthetic oil meeting ILSAC GF-2,API certification mark and API service symbol with “SJ/CF ENERGY CONSERVING” or higher, is an acceptable oil for use at all temperatures. Use of synthetic oil does not alter required oil change intervals.

Inspecting Engine Oil Level

Inspect oil level prior to each use or at least every 8 hours of operation. Keep oil level maintained.

1.Make sure unit is on a level surface.

2.Remove Oil Fill Cap and wipe clean with cloth.

3.Verify oil is at the point of overflowing at oil fill opening.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 074002 Call Helpline Appelez Ligne dassistance Llame Línea DirectaSafety Rules Table of ContentsEquipment Description Hazard Symbols and Meanings Safety RulesSafety Rules When Adjusting or Making Repairs to Your AIR Compressor When Testing for Engine SparkWhen Adding or Draining Fuel When Starting EquipmentAssembly Carton ContentsUnpacking Verify Engine and Pump Oil LevelsInstall Pump Oil Breather Cap Fuel Level IndicatorDrain Valve shown in Open position Oil Fill LocationFeatures and Controls Features and ControlsCompressor Oil Fill Location Fill pump with oil here.Oil Quick Connect Fittings Connect air hoses hereBreak-In Procedure OperationAir Compressor Operating Location OperationStarting Your Air Compressor Start valve is shown in Closed positionTransport Stopping Your Air CompressorUse the handles to lift or carry the unit Compressor Operation Pressure ControlSpecifications Power RatingsSpecifications Product SpecificationsMaintenance MaintenanceMaintenance Service Dates Service Intervals Maintenance TaskMaintenance Cleaning UnitGeneral Recommendations Emissions ControlInspect Safety Valve Inspect Quick Connect Fittings and Tank Drain ValvesInspect Engine Oil Level Oil RecommendationsInspect Engine Air Cleaner To service the air cleaner, follow these stepsInspect Pump Oil Level Changing Engine OilCalling Clean Spark Arrester ScreenOil Fill Opening Filter Housing Inspect / Clean Pump Air FilterChanging Pump Oil Inspect Safety Labels Maintenance / StorageStorage Inspect Spark PlugWhen Draining Fuel Other Storage TipsStorage Change OilTroubleshooting TroubleshootingBefore You Call Operate accessories Lacks power startsCompressor is not Supplying enough air toGlossary GlossaryEmissions Emissions Control System Warranty Owner’s Warranty ResponsibilitiesWarranty Period Limited WarrantyTable DES Matières Description DE L’ÉQUIPEMENTRègles DE Sécurité AvertissementSymboles de risque et leur signification Règles DE SécuritéChoc électrique Explosion Objets volants SurfaceAvertissement Mise EN Garde Lors DE Tests D’ALLUMAGE DU MoteurAssemblage AssemblageInstallez le bouchon reniflard de la pompe à lhuile Fonctions ET Commandes Fonctions ET CommandesEmplacement du compresseur d’air lors de l’utilisation FonctionnementFonctionnement Procédure de rodageDémarrage de votre compresseur d’air Tournez l’interrupteur ON/OFF du moteur à la position OFFSuivez les directives de démarrage suivantes Le levier d’étrangleur est illustré à la position ChokeTransport Arrêt de votre compresseur d’airFermez les robinets de vidange Manomètre de pression Bouton de De sortie Utilisation du compresseurPression Spécifications CaractéristiquesPuissance nominale Caractéristiques du produitEntretien EntretienRecommandations générales Contrôle des émissionsEntretien Nettoyage de l’unitéRecommandations relatives à l’huile Vérifiez la soupape de sûretéVérifiez le niveau d’huile du moteur Vérification du niveau d’huile du moteurVérifiez le niveau d’huile de la pompe Vérifiez le filtre à air du moteurVidange de l’huile moteur Vérification du niveau d’huile de la pompeBouchon de vidange d’huile Orifice de Nettoyage de l’écran pare-étincellesUtilisez un entonnoir et videz lentement de l’huile environ Vérifiez/nettoyez le filtre à air de la pompe Changement d’huile de la pompeFiltre à air CompresseurEntreposage Entretien / EntreposageVérification de la bougie Vérifiez les étiquettes de sécuritéEntreposage Autres conseils d’entreposageChangement de l’huile Huilage de l’alésage du cylindreProblème Cause Solution DépannageDépannage Avant de nous contacterAccessoires Le compresseur ne fournitPas suffisamment d’air pour Le fonctionnement des Le moteur ne démarre pasGlossaire GlossaireÉmissions Garantie DU Dispositif Antipollution Période DE Garantie Garantie LimitéeTabla DE Contenido Descripción DEL EquipoNormas DE Seguridad AdvertenciaNormas DE Seguridad Símbolos de peligro y sus significadosAire ExplosiónAdvertencia Precaución Cuando Ajuste O Repare EL Compresor DE AireMontaje MontajeInstalación del tapón del respirador del aceite de la bomba Tapón del respiradorDel aceite Punto de llenadoCaracterísticas Y Mandos Características Y MandosDel motor Estranguladora Filtro de aire Válvula delFuncionamiento FuncionamientoColocación del compresor de aire Procedimiento de preparación para el uso inicialPuesta en marcha del compresor de aire AbiertaDespués de que el compresor de aire funcione durante Palanca en la posiciónParada del compresor de aire TransporteMueva la palanca estranguladora hacia la posición FuncionamientoUso del compresor Figura 56 Control de presiónEspecificaciones EspecificacionesPotencia nominal Especificaciones del productoMantenimiento MantenimientoRecomendaciones generales Control de emisionesMantenimiento Limpieza de la unidadInspeccione la válvula de seguridad Inspeccione el nivel de aceite del motorRecomendaciones sobre el aceite Inspección del nivel de aceite del motorInspeccione el nivel de la bomba de aceite Inspeccione el filtro de aire del motorCambio del aceite del motor Inspección del nivel de la bomba de aceiteLimpieza de la pantalla apagachispas Tapón de vaciado de aceiteInspeccione/limpie el filtro de aire de la bomba Cambio del aceite de la bombaAlmacenamiento MANTENIMIENTO/ALMACENAMIENTORevisión de la bujía Inspección de las etiquetas de seguridadAlmacenamiento Otras sugerencias para el almacenamientoCambio de aceite Aceite en el interior del cilindroResolución DE Problemas Resolución DE ProblemasProblema Motivo Corrección Antes de llamarOFF Glosario GlosarioNotas Emisiones Garantía DEL Sistema DE Control DE Emisiones Período DE Garantía Garantía Limitada
Top Page Image Contents