Toshiba STE 58760 instruction manual Table of Contents

Page 6

STE 58760

TABLE OF CONTENTS

CHAPTER 1 BEFORE OPERATING SR SERIES ROBOT

1.1OVERVIEW・・・・・・・・・・・・・・・・・・・・・・・・・ 1-1

1.1.1Structure・・・・・・・・・・・・・・・・・・・・・・・・・ 1-2

1.1.2Functions・・・・・・・・・・・・・・・・・・・・・・・・・ 1-4

1.2 OUTLINE OF OPERATIONAL PROCEDURE ・・・・・・・・・・ 1-9

1.3SPECIFICATIONS・・・・・・・・・・・・・・・・・・・・・・ 1-11

1.4COORDINATE SYSTEM・・・・・・・・・・・・・・・・・・・・ 1-14

1.5SYSTEM CONFIGURATION・・・・・・・・・・・・・・・・・・ 1-16

1.6 NAMES AND FUNCTIONS OF SR7000 CONTROLLER・・・・・ 1-21

1.6.1C o n t r o l P a n e l ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 1-21

1.6.2Teach Pendant・・・・・・・・・・・・・・・・・・・・・・ 1-23

CHAPTER 2 POWER ON TO MANUAL GUIDANCE

2.1

TURNING ON MAIN POWER・・・・・・・・・・・・・・・・・

2-2

2.1.1

Cold Starting・・・・・・・・・・・・・・・・・・・・・・・

2-2

2.1.2

Hot Starting・・・・・・・・・・・・・・・・・・・・・・・・

2-5

2.2

SETTING CONTROLLER ENVIRONMENTAL CONDITIONS・・・

2-8

2.3

TURNING THE SERVO POWER ON・・・・・・・・・・・・・・

2-9

2.4

MANUAL GUIDANCE OF EACH AXIS・・・・・・・・・・・・・

2-10

2.5MANUAL GUIDANCE OPERATION・・・・・・・・・・・・・・ 2-13

2.6MOTION RANGE LIMIT・・・・・・・・・・・・・・・・・・・ 2-16

2.6.1

Setting Joint Limit Values by Teaching・・・・・・・・・・・・

2-16

2.6.2

Setting Joint Limit by Numeric Value Entry・・・・・・・・・・

2-18

v

Image 6
Contents Industrial Robot SR Series START-UP Manual - i - Preface For Euporean Union EU - iv - Table of Contents Changing File DATA・・・・・・・・・・・・・・・・・・・・ Backing UP FILES・・・・・・・・・・・・・・・・・・・・・ Chapter Before Operating SR Series Robot Overview- 1-2 - - 1-3 - - 1-4 - PTP - 1-6 - - 1-7 - - 1-8 - Outline of Operational Procedure -1-10- Specifications -1-12- -1-13- Coordinate System -1-15- System Configuration -1-17- -1-18- -1-19- STE -1-20- Names and Functions of SR7000 Controller Control PanelPower LED Fault LEDTeach Pendant -1-24- -1-25- -1-26- STE -1-27- -1-28- Chapter Power on to Manual Guidance Turning on Main Power Cold Starting- 2-3 - Edit Load Save Testrun Reset Next Hot Starting - 2-6 - - 2-7 - Setting Controller Environmental Conditions Turning the Servo Power on Manual Guidance of Each Axis -2-11- -2-12- Manual Guidance Operation -2-14- -2-15- Setting Joint Limit Values by Teaching Motion Range LimitFormat Verify Zerop Jlimit Channel Next Next Jlimit Travel Joint Negative PositiveSetting Joint Limit by Numeric Value Entry Channel Next-2-19- Travel Joint Negative Positive Turning OFF the Power Turning OFF Servo PowerTurning OFF the Main Power -2-22- -2-23- Setting Date and Time Setting DateDate Date Time Next Setting Time Date Time NextTime Date Time Next - 3-5 - Changing File Data Edit CONSTRUC.SYS Edit Load Save Testrun Reset Next - 3-8 - - 3-9 - -3-10- -3-11- Setting the System Configuration Outline of Data-3-13- Construction of MANIPULATER. =0WITHOUT,=1WITH Specify for Gravity Compensation Servo Free ModeFile Format Type of JOINT=0LINEAR.=1ROTATE, 1ST Joint to 5THMode of Channel COM1 Specify for External File Selection SignalMode of Serial Channel Mode of Channel COM2Mode of AIR Driven Axis Specify for USE or not USE -3-17- Details of Data -3-19- -3-20- -3-21- PRT Host=HOST -3-24- -3-25- Setting External Selection Files Signals Used for Selecting FileContents of File -3-28- Batch Processing Batch File-3-30- Automatic Execution File LOADPRO1 LOADPRO2 LOADPRO3 LOADPRO4 Loadpros LOADPRO6Using Batch Processing Effectively Select PRO1Loadconstruc .SYS LOADSYSTEM. PAR LOADUSER. PAR LOAD*. PRO -3-33- Program Execution Environment Program Execution Environment-3-35- Resetting Execution Environment Reset Timing of Program Execution Environment Setting Coordinate System Robot Coordinate Systems-3-39- Teaching Coordinate Data System and the original coordinate system unit deg-3-41- Program Sample Move P1 Move P2 END -3-43- -3-44- -3-45- Selecting Coordinate System in Data Editor Mode -3-47- Z,C,T RightyLefty -3-49- -3-50- -3-51- -3-52- Selecting Coordinate System in Utility Mode Robot Utility Work Tool Where Signal Memory -3-55- Selecting Coordinate System Using Robot Language Timing of Changing Coordinate System