Toshiba STE 58760 instruction manual Changing File Data

Page 65

STE 58760

3.2CHANGING FILE DATA

To edit files including the system configuration file, use the screen editor function. The basic operation of the screen editor is as follows:

(1)Turn on the main power of the controller and place the MASTER MODE KEY switch on the control panel in the "MANU" position. The following controller monitor command menu appears at the bottom of the teach pendant LCD display.

>■

EDIT LOAD SAVE TESTRUN> RESET NEXT

F1

F2

F3

F4

F5

F6

(2)Whenever you press the teach pendant "F6" key, the monitor command menu changes accordingly. Repeat this key operation until the "EDIT" command appears.

NEXT

F6

－ 3-6 －

Image 65

Contents Industrial Robot SR Series START-UP Manual － i － Preface For Euporean Union EU － iv － Table of Contents Changing File DATA・・・・・・・・・・・・・・・・・・・・ Backing UP FILES・・・・・・・・・・・・・・・・・・・・・ Overview Chapter Before Operating SR Series Robot－ 1-2 －－ 1-3 －－ 1-4 － PTP － 1-6 －－ 1-7 －－ 1-8 － Outline of Operational Procedure －1-10－ Specifications －1-12－－1-13－ Coordinate System －1-15－ System Configuration －1-17－－1-18－－1-19－ STE －1-20－ Control Panel Names and Functions of SR7000 ControllerFault LED Power LEDTeach Pendant －1-24－－1-25－－1-26－ STE －1-27－－1-28－ Chapter Power on to Manual Guidance Cold Starting Turning on Main Power－ 2-3 － Edit Load Save Testrun Reset Next Hot Starting － 2-6 －－ 2-7 － Setting Controller Environmental Conditions Turning the Servo Power on Manual Guidance of Each Axis －2-11－－2-12－ Manual Guidance Operation －2-14－－2-15－ Format Verify Zerop Jlimit Channel Next Setting Joint Limit Values by TeachingMotion Range Limit Jlimit Travel Joint Negative Positive NextChannel Next Setting Joint Limit by Numeric Value Entry－2-19－ Travel Joint Negative Positive Turning OFF the Main Power Turning OFF the PowerTurning OFF Servo Power －2-22－－2-23－ Setting Date Setting Date and TimeDate Date Time Next Date Time Next Setting TimeTime Date Time Next － 3-5 － Changing File Data Edit CONSTRUC.SYS Edit Load Save Testrun Reset Next － 3-8 －－ 3-9 －－3-10－－3-11－ Outline of Data Setting the System Configuration－3-13－ File Format Specify for Gravity Compensation Servo Free ModeConstruction of MANIPULATER. =0WITHOUT,=1WITH Type of JOINT=0LINEAR.=1ROTATE, 1ST Joint to 5THMode of Serial Channel Specify for External File Selection SignalMode of Channel COM1 Mode of Channel COM2Mode of AIR Driven Axis Specify for USE or not USE －3-17－ Details of Data －3-19－－3-20－－3-21－ Host PRT=HOST －3-24－－3-25－ Signals Used for Selecting File Setting External Selection FilesContents of File －3-28－ Batch File Batch Processing－3-30－ LOADPRO1 LOADPRO2 LOADPRO3 LOADPRO4 Loadpros LOADPRO6 Automatic Execution FileLoadconstruc .SYS LOADSYSTEM. PAR LOADUSER. PAR LOAD*. PRO Using Batch Processing EffectivelySelect PRO1 －3-33－ Program Execution Environment Program Execution Environment－3-35－ Resetting Execution Environment Reset Timing of Program Execution Environment Robot Coordinate Systems Setting Coordinate System－3-39－ System and the original coordinate system unit deg Teaching Coordinate Data－3-41－ Program Sample Move P1 Move P2 END －3-43－－3-44－－3-45－ Selecting Coordinate System in Data Editor Mode －3-47－ Lefty Z,C,TRighty －3-49－－3-50－－3-51－－3-52－ Selecting Coordinate System in Utility Mode Robot Utility Work Tool Where Signal Memory －3-55－ Timing of Changing Coordinate System Selecting Coordinate System Using Robot Language