BRUSH REPLACEMENT
&RPSOHWHO\XQVFUHZWKHFDS Fig. 6, A 1H[WSXOOWKHEUXVKRXWIURPWKHEUXVKKROGHU
3.Worn brushes should be replaced in the same
KROGHUDQGSRVLWLRQDVUHPRYHG
4.Re-fasten the cap.
&KHFN WKDW WKH WRRO FDQ RSHUDWH %HIRUH XVH allow it to run for a few minutes to enable the brushes to settle.
Ⱥ
Figure 6
OPERATING THE WRENCH
1.Resting the unit after continuous operation.
$IWHU FRQWLQXRXV RSHUDWLRQ OHDYH WKH SRZHU tool for 15 minutes or so to rest when replac-
ing the battery. The temperature of the motor, switch, etc., will rise if operation is started again
LPPHGLDWHO\DIWHUEDWWHU\UHSODFHPHQWHYHQWX- ally resulting in burnout.
3ODFH WKH SRLQW RI WKH GULYHU ELW LQ WKH VFUHZ head. Keep the tool pointed straight at the screw.
$SSO\IRUZDUGSUHVVXUHWRWKHWRROWRSUHYHQWWKH bit from slipping off the screw.
4.Turn the power tool on to start operation. Always check torque with a torque wrench, as the fastening torque is affected by many factors
LQFOXGLQJWKHIROORZLQJ
9ROWDJH | /RZYROWDJHGXHWRDQHDUO\ | |
discharged battery, will re- | ||
| duce the fastening torque. | |
|
| |
%LWRUVRFNHW | )DLOXUHWRXVHWKHFRUUHFWELW | |
RUVRFNHWVL]HZLOOFDXVHD | ||
VL]H | ||
reduction in fastening torque. | ||
| ||
|
| |
Variable speed | Operating the tool at a | |
reduced speed will decrease | ||
WULJJHUVZLWFK | the fastening torque. | |
| ||
|
| |
| /DUJHUEROWGLDPHWHUVJHQHU- | |
| ally require higher fastening | |
%ROWVL]H | WRUTXH)DVWHQLQJWRUTXHZLOO | |
| DOVRYDU\DFFRUGLQJWROHQJWK | |
| JUDGHDQGWRUTXHFRHI¿FLHQW |
| The type of material and sur- |
0DWHULDO | IDFH¿QLVKRIWKHPDWHULDOZLOO |
| affect fastening torque. |
| /RQJHUIDVWHQLQJWLPHUHVXOWV |
| in increased fastening torque. |
)DVWHQLQJWLPH | Using a longer fastening |
time than recommended | |
| could cause the screws to |
| EHRYHUVWUHVVHGVWULSSHGRU |
| damaged. |
5HIHUHQFH YDOXHV IRU WKH SURSHU IDVWHQLQJ WRUTXH based on a standard bolt and resist high tension bolt DUHSURYLGHGKHUH Fig. 7 & 8
Figure 7
Figure 8
CAUTION: Metalcasecangethotduring continuous operation.
1.Cautions on use of the speed control switch. This switch has a
FDQ YDU\ WKH URWDWLRQ VSHHG &RQVHTXHQWO\ when the switch trigger is pressed only slightly
ORZVSHHGURWDWLRQ DQGWKHPRWRULVVWRSSHG ZKLOHFRQWLQXRXVO\GULYLQJLQVFUHZVWKHFRP-
SRQHQWVRIWKHHOHFWURQLFFLUFXLWSDUWVPD\RYHU- heat and be damaged.
EN 8
GUR 12S
17.3.2006 . 09:59:25