Hitachi hitachi series inverter A058, A059, A061, A261, A062, A262, A063, A065, A067, A064, A066

Page 55


	Func.		Name		Description
	Code		Name		Description
	Code

Run

Mode

Edit

Initialdata Units

a058	DC braking time at start	Sets the duration for DC braking,		0.0	sec.
		range is from 0.0 to 60.0
		seconds
a059	Carrier frequency during DC	Carrier frequency of DC braking		5.0	sec.
a059	braking	performance, range is from 2.0 to
		15.0kHz
A061	Frequency upper limit	Sets a limit on output frequency		0.00	Hz
		less than the maximum
		frequency (A004).
		Range is from frequency lower
		limit (A062) to maximum
		frequency (A004).
		0.0 setting is disabled
		>0.0 setting is enabled
A261	Frequency upper limit,	Sets a limit on output frequency		0.00	Hz
A261	2nd motor	less than the maximum
		frequency (A204).
		Range is from frequency lower
		limit (A262) to maximum
		frequency (A204).
		0.0 setting is disabled
		>0.0 setting is enabled
A062	Frequency lower limit	Sets a limit on output frequency		0.00	Hz
		greater than zero.
		Range is start frequency (B082)
		to frequency upper limit (A061)
		0.0 setting is disabled
		>0.0 setting is enabled
A262	Frequency lower limit,	Sets a limit on output frequency			Hz
	Frequency lower limit,	Sets a limit on output frequency		0.00	Hz
	2nd motor	greater than zero.
		Range is start frequency (B082)
		to frequency upper limit (A261)
		0.0 setting is disabled
		>0.0 setting is enabled
A063	Jump freq. (center) 1 to 3	Up to 3 output frequencies can		0.0	Hz
A065		be defined for the output to jump		0.0
A065		past to avoid motor resonances		0.0
A067		past to avoid motor resonances		0.0
A067		(center frequency)
		Range is 0.0 to 400.0 Hz
A064	Jump freq. width (hysteresis) 1	Defines the distance from the		0.5	Hz
A066	to 3	center frequency at which the		0.5
A068		jump around occurs		0.5
A068		Range is 0.0 to 10.0 Hz
A069	Acceleration hold frequency	Sets the frequency to hold		0.00	Hz
		acceleration, range is 0.0 to
		400.0Hz
A070	Acceleration hold time	Sets the duration of acceleration		0.0	sec.
		hold, range is 0.0 to 60.0
		seconds
A071	PID enable	Enables PID function,		00	−
		three option codes:
		00…PID Disable
		01…PID Enable
		02…PID Enable with reverse
		output

53

Image 55

Contents WJ200 Series Inverter Quick Reference Guide Page UL→ Cautions, Warnings and Instructions Marking RequirementsTerminal symbols and Screw size Fuse Sizes 5AT 123 45A-001 1005 Inverter Specification LabelModel-specific tables for 200V and 400V class inverters WJ200 Inverter SpecificationsWJ200 Inverter Specifications, … WJ200 inverters, 400V models Derating GFI Basic System DescriptionInverter + Motor Output Determining Wire and Fuse SizesAllowable current T1 V/T2 W/T3 L1 S/L2 T/L3 U/T1 V/T2 W/T3 Wire the Inverter Input to a SupplyRB PD/+1 P/+ Three-phase 200V 11kW Three-phase 400V 11, 15kW Key and Indicator Legend Using the Front Panel KeypadPower LED Alarm LED Keypad Navigation Map Keys, Modes, and ParametersPRG LED Group a Group dGroup F SaveF001 Key GND Connecting to PLCs and Other DevicesMotor Example Wiring DiagramOutput Input Control Logic Signal SpecificationsPulse TrainSP, SN Wiring sample of control logic terminal sink logicSink/source logic of intelligent input terminals Wire size for control and relay terminalsRecommended ferrule Intelligent Inputs Intelligent Terminal ListingIntelligent Outputs Sink logic connection Using Intelligent Input TerminalsSource logic connection WJ200 Sinking Inputs, Internal SupplySourcing Inputs, Internal Supply Sourcing Inputs, External Supply Sinking Inputs, External SupplyOFF InsertingOption Terminal Code Symbol Function Name State Description Forward Run/Stop and Reverse Run/Stop CommandsMulti-Speed Select ~Binary Operation Required settingsFW,RV Two Stage Acceleration and Deceleration2CH Unattended Start Protection Option Terminal Function Name State Description Code SymbolUSP Reset Inverter Option Terminal Function Name Using Intelligent Output TerminalsRun Signal Code SymbolSettings Frequency Arrival SignalsRequired FA3/FA5 FA2/FA4Stop Alarm SignalTrip During normal operation AM H O OI L Analog Input OperationAM H O OI Other Analog Input-related topics SN 7 6 5 4 3 2 1 L PLC P24 Pulse Train Input OperationAnalog Output Operation AM signal offset and gain are adjustable, as indicated below Monitoring functions D009 D006D007 D008D060 D029D030 D050Main Profile Parameters Standard Functions A021 ~ A035 A015A220 A241A044 A242A043 A243A261 A058A059 A061A075 A072A073 A074A293 A092A292 A093A142 A131A132 A141A162 A156A157 A161Fine Tuning Functions B213 B012B212 B013B028 B025B026 B027B040 B037B038 B039B063 B060B061 B062B090 B087B088 B089B101 B096B097 B100B150 B133B134 B145Intelligent Terminal Functions C032 C028C030 C031C054 C047C052 C053C081 C076C077 C078C105 C102C103 C104C150 C147C148 C149DWN AnlgFWD, REV PidcSF4 SF1SF2 SF3255 Run Signal When the inverter is in Run Mode LOG2 LOG1LOG3 MO3 C039MO1 MO2Motor Constants Functions PM Motor Constants Functions H117 H112H113 H116Expansion Card Functions P046 P041P044 P045P077 P072P073 P075Trip History and Inverter Status Monitoring Trip Events, History, & ConditionsError Name Causes Code Error CodesE37 Error Name Descriptions Code Restoring Factory Default SettingsOther indication Important notes CE-EMC Installation GuidelinesPage Page Metal plate earth Installation for WJ200 series example of SF modelsHitachi EMC Recommendations How it works Functional Safety Certification in ProgressIntroduction Stop Category defined in EN60204-1Installation Wiring example OFF G9SX GS9ANE1A