Makita HR5212C instruction manual Optional Accessories, Lubrication

Page 9

Lubrication

CAUTION:

This servicing should be performed by Makita Authorized Service Centers only.

Do not perform lubrication just after the operation, wait until the tool cools down. Otherwise skin burn may result.

This tool requires no hourly or daily lubrication because it has a grease-packed lubrication system. However, it is necessary to replace grease and carbon brushes periodically for tool’s long life.

(For model HR4003C, HR5202C) Loosen the six screws and remove the handle. (Fig. 22)

(For model HR4013C, HR5212C) Loosen the eight screws. And remove the guard cover as shown in the figure. And then remove the handle. (Fig. 23 & 24)

Remove the connector by pulling it. (Fig. 25) Loosen the screws and remove the change lever. Remove the crank cap cover. (Fig. 26)

Remove the control plate. (Fig. 27)

Loosen the six screws and remove the crank cap. Rest the tool on the table with the bit end pointing upwards. This will allow the old grease to collect inside the crank housing. (Fig. 28)

Wipe out the old grease inside and replace with fresh grease:

For model HR4003C, HR4013C: 30 g

For model HR5202C, HR5212C: 60 g

Use only Makita genuine hammer grease (optional accessory). Filling with more than the specified amount of grease can cause faulty hammering action or tool failure. Fill only with the specified amount of grease.

(Fig. 29)

Reinstall all removed parts.

Attach the connector and reinstall the handle. (Fig. 30)

NOTE:

• Note that the different lengths of screws are used.

NOTICE

Do not tighten the crank cap excessively. It is made of resin and is subject to breakage.

Be careful not to damage the connector or lead wires especially when wiping out the old grease or installing the handle.

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.

If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.

SDS-MAX Carbide-tipped bits

SDS-MAX bull point

SDS-MAX cold chisel

SDS-MAX scaling chisel

SDS-MAX clay spade

Hammer grease

Bit grease

Side handle

Side grip

Depth gauge

Blow-out bulb

Safety goggles

Carrying case

Dust extractor attachment

NOTE:

Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.

ENG905-1

Noise

The typical A-weighted noise level determined according to EN60745:

Model HR4003C, HR4013C

Sound pressure level (LpA): 92 dB (A)

Sound power level (LWA): 103 dB (A)

Uncertainty (K): 3 dB (A)

Model HR5202C

Sound pressure level (LpA): 99 dB (A)

Sound power level (LWA): 110 dB (A)

Uncertainty (K): 3 dB (A)

Model HR5212C

Sound pressure level (LpA): 98 dB (A)

Sound power level (LWA): 109 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum) determined according to EN60745:

Model HR4003C

Work mode: chiseling function with side handle

Vibration emission (ah, CHeq): 9.0 m/s2

Uncertainty (K): 1.5 m/s2

Work mode: chiseling function with side grip

Vibration emission (ah, CHeq): 9.0 m/s2

Uncertainty (K): 1.5 m/s2

Work mode: hammer drilling into concrete

Vibration emission (ah, HD): 10.0 m/s2

Uncertainty (K): 1.5 m/s2

Model HR4013C

Work mode: chiseling function with side handle

Vibration emission (ah, CHeq): 4.5 m/s2

Uncertainty (K): 1.5 m/s2

Work mode: chiseling function with side grip

Vibration emission (ah, CHeq): 4.5 m/s2

Uncertainty (K): 1.5 m/s2

Work mode: hammer drilling into concrete

Vibration emission (ah, HD): 5.0 m/s2

Uncertainty (K): 1.5 m/s2

Model HR5202C

Work mode: chiseling function with side handle

Vibration emission (ah, CHeq): 10.5 m/s2

Uncertainty (K): 1.5 m/s2

Work mode: chiseling function with side grip

Vibration emission (ah, CHeq): 10.5 m/s2

Uncertainty (K): 1.5 m/s2

9

Image 9
Contents HR4003C HR4013C HR5202C HR5212C 014028 014029 014880 014022 014024 014023 014032 003139 014034 014027 014878 014090 003150 014879 014091 014135 014036 General Power Tool Safety Warnings SpecificationsRotary Hammer Safety Warnings Explanation of general viewSelecting the action mode Switch actionFunctional Description Speed change FigAssembly MaintenanceOperation Lubrication Optional AccessoriesEC Declaration of Conformity For European countries onlyConforms to the following European Directives 2006/42/EC Consignes DE Sécurité Pour Marteau SpécificationsPerforateur ÉlectriquesDescription DU Fonctionnement Conservez CES InstructionsInterrupteur Changement de vitesse FigAssemblage Entretien UtilisationAccessoires EN Option Déclaration de conformité CE Pour les pays d’Europe uniquementSont conformes aux directives européennes suivan- tes Sicherheitswarnungen FÜR Technische DatenBohrhammer Allgemeine Sicherheitswarnungen fürFunktionsbeschreibung Bewahren SIE Diese Hinweise Sorgfältig AUFSchalterfunktion Drehzahlumschaltung AbbMontage Wartung BetriebSonderzubehör EG-Übereinstimmungserklärung Nur für europäische LänderDen folgenden europäischen Richtlinien entspre- chen Avvertimenti PER LA Sicurezza DEL Dati TecniciMartello Rotativo Avvertimenti generali per la sicurezzaDescrizione Funzionale Conservare Queste IstruzioniFunzionamento dell’interruttore Cambio di velocità FigMontaggio Accessori Opzionali FunzionamentoManutenzione Modello HR5202C RumoreModello HR5212C Indossare i paraorecchieDichiarazione CE di conformità Modello per l’Europa soltantoConforme alle Direttive Europee 2006/42/CE Veiligheidsvoorschriften Voor DE Technische GegevensBoorhamer Elektrisch gereedschapBeschrijving VAN DE Functies Bewaar Deze VoorschriftenSchakelaarwerking Snelheid regelen FigIneenzetten Onderhoud BedieningGeluidsniveau Optionele AccessoiresDraag oorbeschermers TrillingEU-Verklaring van Conformiteit Alleen voor Europese landenVoldoet aan de volgende Europese Richtlijnen 2006/42/EU Advertencias DE Seguridad Para EL EspecificacionesHerramientas eléctricas Explicación de los dibujosDescripción DEL Funcionamiento Guarde Estas InstruccionesAccionamiento del interruptor Cambio de velocidad FigMontaje Operación MantenimientoAccesorios Opcionales Modelo HR4003C, HR4013C RuidoModelo HR5202C Modelo HR5212CDeclaración de conformidad CE Para países europeos solamenteCumplen con las directivas europeas siguientes 2006/42/CE Avisos DE Segurança Para O Martelo EspecificaçõesRotativo EléctricasDescrição Funcional Guarde Estas InstruçõesAcção do interruptor Mudança de velocidade FigOperação AssemblagemAcessórios Opcionais ManutençãoSoprador acessório opcional Fig Aparar/Descascar/Demolir FigDeclaração de conformidade CE Sikkerhedsadvarsler for SpecifikationerBorehammer IllustrationsoversigtFunktionsbeskrivelse GEM Denne BrugsanvisningAfbryderanvendelse Hastighedsændring FigBetjening SamlingEkstraudstyr VedligeholdelseUdblæsningskugle ekstraudstyr Fig Mejselarbejde/afskalning/nedbrydning FigEU-konformitetserklæring Kun for lande i EuropaEr i overensstemmelse med de europæiske direktiver Προειδοποιησεισ Ασφαλειασ ΓΙΑ ΤΟ Τεχνικα ΧαρακτηριστικαΠεριστροφικο Σφυρι Γενικές προειδοποιήσεις ασφαλείας για τοΠεριγραφη Λειτουργιασ Φυλαξτε ΤΙΣ Οδηγιεσ ΑυτεσΔράση διακόπτη Αλλαγή ταχύτητας ΕικΣυναρμολογηση Συντηρηση ΛειτουργιαΠροαιρετικα Εξαρτηματα Μόνο για χώρες της Ευρώπης Δήλωση Συμμόρφωσης ΕΚMakita δηλώνει ότι τα ακόλουθα μηχανήματα Συμμορφώνονται με τις ακόλουθες Ευρωπαϊκές ΟδηγίεςKirici Delİcİ Matkap Güvenlİk ÖzellİklerUyarilari Genel elektrikli alet Güvenliği Uyarılarİşlevsel Açiklamalar BU Talİmatlari SaklayinAnahtar işlemi Hız değişimi ŞekKullanim Montajİsteğe Bağli Aksesuarlar BakimToz üfleme aparatı isteğe bağlı aksesuar Şek Yontma/Raspalama/Kırma ŞekEC Uygunluk Beyanı Page Page Makita Corporation Anjo, Aichi, Japan