Panasonic EY4541 Battery Charger Charging, Battery Recycling, Li-ion Battery Pack

Page 16

Battery Recycling

ATTENTION:

FOR Li-ion Battery Pack, EY9L40

A Li-ion battery that is recyclable pow- ers the product you have purchased. Please call 1-800-8-BATTERY for infor- mation on how to recycle this battery.

[Battery Charger]

Charging

Cautions for the Li-ion Battery Pack

If the temperature of the battery pack falls approximately below −10°C (14°F), charging will auto- matically stop to prevent degrada- tion of the battery.

Common Cautions for the Li- ion/Ni-MH/Ni-Cd Battery Pack

The ambient temperature range is be- tween 0°C (32°F) and 40°C (104°F). If the battery pack is used when the battery temperature is below 0°C (32°F), the tool may fail to function properly.

When charging a cool battery pack (below 0°C (32°F)) in a warm place, leave the battery pack at the place and wait for more than one hour to warm up the battery to the level of the ambient temperature.

Cool down the charger when charg- ing more than two battery packs consecutively.

Do not insert your fingers into con- tact hole, when holding charger or any other occasions.

CAUTION:

To prevent the risk of fire or damage to the battery charger.

Do not use power source from an engine generator.

Do not cover vent holes on the charger and the battery pack.

Unplug the charger when not in use.

Li-ion Battery Pack

NOTE:

Your battery pack is not fully charged at the time of purchase. Be sure to charge the battery before use.

Battery charger (EY0L80)

1.Plug the charger into the AC outlet.

NOTE:

Sparks may be produced when the plug is inserted into the AC power supply, but this is not a problem in terms of safety.

2.Insert the battery pack firmly into the charger.

1.Line up the alignment marks and place the battery onto the dock on the charger.

2.Slide forward in the direction of the arrow.

Alignment marks

3.During charging, the charging lamp will be lit.

When charging is completed, an inter- nal electronic switch will automatically be triggered to prevent overcharging.

Charging will not start if the battery pack is warm (for example, immedi- ately after heavy-duty operation).

The orange standby lamp will be flashing until the battery cools down. Charging will then begin automatically.

4.The charge lamp (green) will flash slowly once the battery is approxi- mately 80% charged.

5.When charging is completed, the charging lamp will start flashing quickly in green color.

6.If the temperature of the battery pack is 0°C or less, charging takes longer to fully charge the battery pack than the standard charging time.

Even when the battery is fully charged, it will have approximately 50% of the power of a fully charged battery at nor- mal operating temperature.

- 16 -

Image 16
Contents Model No EY4541 ImportanteIndex/Index/Indice Switch lock lever II. General Safety Rules Work Area SafetyElectrical Safety Personal SafetyBattery Tool Use and Care Power Tool Use and CareKeep cutting tools sharp and clean Service III. Specific Safety RulesSymbol Meaning IV. for Battery Charger & BAT- Tery Pack Important Safety InstructionsPage Assembly Installing and removing the bladeInstallation Inspection before useRemoval Adjusting the basePosition of base and purpose of use Adjusting the orbital stroke mode Anti-splintering plateVI. Operation Attaching or Removing Battery PackCutting Cutting along marked lines Installing the rip fencePlunge cutting Control Panel Cutting at the same widthCutting circles LED lightBattery Pack For Appropriate Use of Battery pack Li-ion Battery pack EY9L40Battery Pack Life Battery low warning lampBattery Charger Charging Battery RecyclingCommon Cautions for the Li- ion/Ni-MH/Ni-Cd Battery Pack Li-ion Battery PackNi-MH/Ni-Cd Battery Pack VII. Maintenance Lamp IndicationsVIII. Accessories IX. SpecificationsLi-ion battery pack Ni-Cd/Ni-MH battery packSécurité de la zone de travail Sécurité électriqueSécurité personnelle AVERTISSEMENT! Veuillez lireUtilisation et soins de l’outil mécanique Réparation Utilisation et soins de la batterie de l’outilMaintenez les outils de coupe affû- tés et propres Avertissement IV. Chargeur DE Batterie ET BAT- Terie Autonome Instructions de sécurité importantesNe modifiez la fiche en aucune façon Installation et retrait de la lame MontageVérification avant emploi Ajustement de la basePosition de la base et utilisation pré- vue Ajustement du mode de cour- se orbitaleRemarque Plaque anti-éclat Fixation ou retrait de la batte- rie autonomeDécoupe VI. UtilisationDécoupe le long de lignes marquées Installation du guide à refendre Sciage en plongéeDécoupe à la même épaisseur Découpe de cerclesPanneau de commande Lumière DELMise EN Garde Témoin davertissement de sur- chauffeBatterie autonome Chargeur de batterie RechargeBatterie autonome Li-ion Chargeur de batterie EY0L80Batterie autonome Ni-MH/Ni-Cd Indication DU Voyant VII. Entretien VIII. AccessoiresIX. Caractéristiques Techniques Batterie autonome Li-ion Batterie autonome Ni-MH/Ni-CdIntroducción Seguridad del lugar de trabajoSeguridad eléctrica Seguridad personalUso y cuidados de he- rramientas eléctricas Servicio Uso y cuidado de la he- rramienta a bateríaMantenga las herramientas de cor- te afiladas y limpias Advertencia … min-1Revoluciones o reciproca- ciones por minutoIV. Para EL CARGA- DOR DE Bateria Y LA Bateria Instrucciones de seguridad importantesNo cambie el enchufe de ninguna for- ma Montaje Inspección antes del usoInstalación y remoción de la cuchilla Ajuste de la basePosición de la base y propósito de uso Ajuste del modo de recorrido orbitalNota Placa anti-astillado Colocación y extracción de la bateríaCortado Corte a lo largo de las líneas marcadasCorte inmerso Instalación del alineador de aserra- doCorte con el mismo ancho Corte de círculosPanel de control Luz indicadoraPrecaución Luz de advertencia de sobrecalen- tamientoBatería Para un uso adecuado de la batería Cargador de la batería CargaBatería Ni-MH/Ni-Cd Batería de Li-iónCargador de batería EY0L80 Meta firmemente la batería en el carga- dor Indicación DE LA Lámpara VIII. Accesorios VII. MantenimientoIX. Especificaciones Cargador DE Batería Batería Ni-MH/Ni-CdMemo Memo Memo Panasonic Consumer Electronics Company
Related manuals
Manual 176 pages 57.68 Kb