Panasonic EY4541 Battery Pack For Appropriate Use of Battery pack, Li-ion Battery pack EY9L40

Page 15

(2) Overheat warning lamp

Off

Flashing: Overheat

(normal

Indicates operation

operation)

has been halted due to

 

battery overheating.

The overheating protection feature halts operation to protect the battery pack in the event of overheating. The overheat warning lamp on the control panel flashes when this feature is ac- tive.

If the overheating protection feature activates, allow the driver to cool thor- oughly (at least 30 minutes). The bat- tery is ready for use when the over- heat warning lamp goes out.

Avoid using the driver in a way that causes the overheating protection fea- ture to activate repeatedly.

(3)Battery low warning lamp

Off

Flashing

(normal

(No charge)

operation)

Battery protection

 

feature active

Excessive (complete) discharging of lithium ion batteries shortens their ser- vice life dramatically. The tool includes a battery protection feature designed to prevent excessive discharging of the battery pack.

The battery protection feature ac- tivates immediately before the bat- tery loses its charge, causing the battery low warning lamp to flash.

If you notice the battery low warning lamp flashing, charge the battery pack immediately.

[Battery Pack]

For Appropriate Use of Battery pack

Li-ion Battery pack (EY9L40)

For optimum battery life, store the Li-ion battery pack following use without charging it.

When charging the battery pack, confirm that the terminals on the bat- tery charger are free of foreign sub- stances such as dust and water etc. Clean the terminals before charging the battery pack if any foreign sub- stances are found on the terminals.

The life of the battery pack termi- nals may be affected by foreign sub- stances such as dust and water etc. during operation.

When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another.

Shorting the battery terminals to- gether may cause sparks, burns or a fire.

When operating the battery pack, make sure the work place is well ventilated.

When the battery pack is removed from the main body of the tool, re- place the battery pack cover imme- diately in order to prevent dust or dirt from contaminating the battery terminals and causing a short circuit.

Battery Pack Life

The rechargeable batteries have a limited life. If the operation time be- comes extremely short after recharg- ing, replace the battery pack with a new one.

- 15 -

Image 15
Contents Importante Model No EY4541Index/Index/Indice Switch lock lever Personal Safety II. General Safety RulesWork Area Safety Electrical SafetyPower Tool Use and Care Battery Tool Use and CareKeep cutting tools sharp and clean III. Specific Safety Rules ServiceSymbol Meaning Important Safety Instructions IV. for Battery Charger & BAT- Tery PackPage Inspection before use AssemblyInstalling and removing the blade InstallationAdjusting the base RemovalPosition of base and purpose of use Anti-splintering plate Adjusting the orbital stroke modeAttaching or Removing Battery Pack VI. OperationCutting Installing the rip fence Cutting along marked linesPlunge cutting LED light Control PanelCutting at the same width Cutting circlesBattery low warning lamp Battery Pack For Appropriate Use of Battery packLi-ion Battery pack EY9L40 Battery Pack LifeLi-ion Battery Pack Battery Charger ChargingBattery Recycling Common Cautions for the Li- ion/Ni-MH/Ni-Cd Battery PackNi-MH/Ni-Cd Battery Pack Lamp Indications VII. MaintenanceIX. Specifications VIII. AccessoriesNi-Cd/Ni-MH battery pack Li-ion battery packAVERTISSEMENT! Veuillez lire Sécurité de la zone de travailSécurité électrique Sécurité personnelleUtilisation et soins de l’outil mécanique Utilisation et soins de la batterie de l’outil RéparationMaintenez les outils de coupe affû- tés et propres Avertissement Instructions de sécurité importantes IV. Chargeur DE Batterie ET BAT- Terie AutonomeNe modifiez la fiche en aucune façon Ajustement de la base Installation et retrait de la lameMontage Vérification avant emploiAjustement du mode de cour- se orbitale Position de la base et utilisation pré- vueRemarque Fixation ou retrait de la batte- rie autonome Plaque anti-éclatVI. Utilisation DécoupeDécoupe le long de lignes marquées Découpe de cercles Installation du guide à refendreSciage en plongée Découpe à la même épaisseurTémoin davertissement de sur- chauffe Panneau de commandeLumière DEL Mise EN GardeChargeur de batterie Recharge Batterie autonomeChargeur de batterie EY0L80 Batterie autonome Li-ionBatterie autonome Ni-MH/Ni-Cd Indication DU Voyant VIII. Accessoires VII. EntretienIX. Caractéristiques Techniques Batterie autonome Ni-MH/Ni-Cd Batterie autonome Li-ionSeguridad personal IntroducciónSeguridad del lugar de trabajo Seguridad eléctricaUso y cuidados de he- rramientas eléctricas Uso y cuidado de la he- rramienta a batería ServicioMantenga las herramientas de cor- te afiladas y limpias … min-1Revoluciones o reciproca- ciones por minuto AdvertenciaInstrucciones de seguridad importantes IV. Para EL CARGA- DOR DE Bateria Y LA BateriaNo cambie el enchufe de ninguna for- ma Ajuste de la base MontajeInspección antes del uso Instalación y remoción de la cuchillaAjuste del modo de recorrido orbital Posición de la base y propósito de usoNota Colocación y extracción de la batería Placa anti-astilladoCorte a lo largo de las líneas marcadas CortadoCorte de círculos Corte inmersoInstalación del alineador de aserra- do Corte con el mismo anchoLuz de advertencia de sobrecalen- tamiento Panel de controlLuz indicadora PrecauciónCargador de la batería Carga Batería Para un uso adecuado de la bateríaBatería de Li-ión Batería Ni-MH/Ni-CdCargador de batería EY0L80 Meta firmemente la batería en el carga- dor Indicación DE LA Lámpara VII. Mantenimiento VIII. AccesoriosIX. Especificaciones Batería Ni-MH/Ni-Cd Cargador DE BateríaMemo Memo Memo Panasonic Consumer Electronics Company
Related manuals
Manual 176 pages 57.68 Kb