Wayne-Dalton 3663-372 Idrive mounts to Lift cables raise door, Security arm manually locks

Page 2

HOW idrive® WORKS

		3
idrive® mounts to the	Lift cables raise door	Security arm manually locks
counterbalance above door.	from bottom.	closed door.

MOUNTS ON THE WALL INSTEAD OF CLUTTERING THE CEILING

Image 2

Contents Important Notice Copyright 2008 Wayne-Dalton Corp Rev 7 7/16/2008Security arm manually locks Idrive mounts to Lift cables raise doorCounterbalance above door From bottom Closed door Package Contents When Installing a NEW Door with AN Idrive Look for this symbolEyes to Prevent Possible Severe or Fatal Injury Pre-InstallationInspection WAYNE-DALTON Track Radius Photoelectric LOW Head System RequirementsTools Needed 10,12,14,15Table of Contents Deﬁnition of key words used in this manualDrum Wrap & End Bracket Retro-Fit InstallationSpring Tension Removal RemovalRemoval End Bracket RemovalTorquemaster Plus Center Bracket & Cable DrumRetro-Fit Installation RETRO-FIT Torquemaster End Bracket RemovalTop Bracket Re-Install If NecessaryVertical Track Height Adjustment 8000/8100/8200 TrackFailure to RE-ATTACH Horizontal RETRO-FIT InstallationsTop Roller Adjustment Tracks to the Support Before Opening Door can Cause DoorInstallation Assembling OpenerIdrive for Torquemaster InstallationCable Drums End Brackets BracketsCable Drum/ Drive Gear InstallationIdrive for Torquemaster Installation End Bracket Installation Counterbalance SpringsAttaching Opener To InstallationPositioning Support Bracket Support BracketSlack between opener and right end Attaching Disconnect CablePliers PliersHandle Bracket Pilot drill lag screw location using 1/8 drill bitMounting Disconnect 6ftDisconnect Attaching Disconnect HandleDisconnect Handle Usage Cable Adjustments Aligned and SeatedTools Needed Vice Clamps Securing DoorFor Spring Winding Winding Springs HandsRecommended Spring Turns Drum Wrap InstallationIMPORTANT! do not Overwind Springs Tools Needed Step LadderSetting Spring Tension IMPORTANT! do not OverwindMounting Wall Station Garage DoorInstalling Battery PRE-OPERATIONInstalling the Light Fixture Attaching Diffuser Connecting OpenerPower Cord Sensor Unit Photoelectric Eyes are notFor Proper Alignment Sensor Wire Installation View of the Opener from the FrontChecking for Obstructions Safety Sensor AlignmentSecuring the Opener Profile Routine Standard Upper Limit On when program button is pushedProgramming Light Fixture On and remain on for 30 secondsCustom Upper Limit Adjusting DetentProfile Routine Work ProperlyLock Arm Installation OperationLock Arm Installation Contact Obstruction TestTesting the Safety Sensors Fatal Injury MAY ResultEmergency Disconnect Read and Follow ALL InstructionsDoor activation Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Programming/Training HomeLink Unit Teaching HomeLink to the idrive openerOperation Multi-Door Programming Customizing the SettingsCustom pet position For more profile options go to page 28Maintenance Confirm pot nut position* shown below Power Connection Permanent Wiring OptionReconnect Power Programming Remote Controls Stations or Transmitters to OpenerProgramming Wireless WallOPENER, Using the Emergency Disconnect Handle Prior toTroubleshooting Symptom Probable Cause Corrective ActionLock Arm Troubleshooting TroubleshootingoperationDalton dealer or distributor Drill Template Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Pre-drill 5/64 pilot holePatent Information

HOW idrive® WORKS

idrive® mounts to the

Lift cables raise door

Security arm manually locks

counterbalance above door.

from bottom.

closed door.

MOUNTS ON THE WALL INSTEAD OF CLUTTERING THE CEILING