Wayne-Dalton 3663-372 Mounting Disconnect, Handle Bracket, 6ft, 4 x 1-1/2 lag screws

Page 21

7	Mounting Disconnect
	Mounting Disconnect
	Handle Bracket

Tools Needed:

Pencil

Tape Measure

Power Drill

1/8" Drill Bit

7/16” Socket

Driver

Mark a location on the right jamb, 6 feet above the floor to mount the disconnect handle bracket.

Pilot drill lag screw location using 1/8" drill bit.

Align top of the bracket with the mark. Fasten bracket to the jamb with

(2) 1/4” x 1-1/2" lag screws.

6ft

1/4” x 1-1/2” Lag Screws

Disconnect

Handle Bracket

IDRIVE® FOR TORQUEMASTER® INSTALLATION

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 14 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 21

Contents Copyright 2008 Wayne-Dalton Corp Rev 7 7/16/2008 Important NoticeIdrive mounts to Lift cables raise door Counterbalance above door From bottom Closed doorSecurity arm manually locks Package Contents Look for this symbol When Installing a NEW Door with AN IdrivePre-Installation InspectionEyes to Prevent Possible Severe or Fatal Injury Tools Needed System RequirementsWAYNE-DALTON Track Radius Photoelectric LOW Head 10,12,14,15Deﬁnition of key words used in this manual Table of ContentsSpring Tension Removal Retro-Fit InstallationDrum Wrap & End Bracket RemovalTorquemaster Plus End Bracket RemovalRemoval Center Bracket & Cable DrumRetro-Fit Installation End Bracket Removal RETRO-FIT TorquemasterVertical Track Height Adjustment Re-Install If NecessaryTop Bracket 8000/8100/8200 TrackTop Roller Adjustment RETRO-FIT InstallationsFailure to RE-ATTACH Horizontal Tracks to the Support Before Opening Door can Cause DoorAssembling Opener InstallationTorquemaster Installation Cable DrumsIdrive for Brackets End BracketsInstallation Idrive for Torquemaster InstallationCable Drum/ Drive Gear Counterbalance Springs End Bracket InstallationPositioning Support Bracket InstallationAttaching Opener To Support BracketPliers Attaching Disconnect CableSlack between opener and right end PliersMounting Disconnect Pilot drill lag screw location using 1/8 drill bitHandle Bracket 6ftAttaching Disconnect Handle Disconnect Handle UsageDisconnect Aligned and Seated Cable AdjustmentsSecuring Door For Spring WindingTools Needed Vice Clamps Hands Winding SpringsIMPORTANT! do not Overwind Springs Drum Wrap InstallationRecommended Spring Turns Tools Needed Step LadderIMPORTANT! do not Overwind Setting Spring TensionGarage Door Mounting Wall StationPRE-OPERATION Installing BatteryInstalling the Light Fixture Connecting Opener Power CordAttaching Diffuser Photoelectric Eyes are not For Proper AlignmentSensor Unit View of the Opener from the Front Sensor Wire InstallationSafety Sensor Alignment Securing the OpenerChecking for Obstructions Programming Light Fixture On when program button is pushedProfile Routine Standard Upper Limit On and remain on for 30 secondsProfile Routine Adjusting DetentCustom Upper Limit Work ProperlyOperation Lock Arm InstallationContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsDoor activation Read and Follow ALL InstructionsEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitOperation Custom pet position Customizing the SettingsMulti-Door Programming For more profile options go to page 28Maintenance Power Connection Permanent Wiring Option Reconnect PowerConfirm pot nut position* shown below OPENER, Using the Emergency Stations or Transmitters to OpenerProgramming Wireless WallProgramming Remote Controls Disconnect Handle Prior toSymptom Probable Cause Corrective Action TroubleshootingTroubleshootingoperation Lock Arm TroubleshootingDalton dealer or distributor Pre-drill 3/32 pilot hole Cut-Out Template to Aid InstallationDrill Template Pre-drill 5/64 pilot holePatent Information