Wayne-Dalton 3663-372 installation instructions Maintenance

Page 45

❉

Customizing the Settings (Continued)

 

Erasing Remote Controls:

CAUTION: MANUALLY DISCONNECT THE DOOR FROM OPENER USING THE EMERGENCY DISCONNECT HANDLE PRIOR TO ERASING REMOTE CONTROLS.

To clear programming of all remote control devices, press and hold the opener’s red program button for approximately 10 seconds. When the opener beeps 3 times, all remote controls are erased.

Multi Opener Light Control:

A single light fixture can be controlled by up to 6 openers. Follow the procedure outlined on Step 23 to program additional openers.

Erasing Light Fixtures:

To clear programming of all openers from a light fixture, press and hold the light fixture program button for approximately 10 seconds. When the light fixture lamp and LED flash 3 times, all openers are erased.

Red

Program

Button

Program Button

OPERATION

❉

Maintenance

 

Monthly Maintenance:

1.Lubricate hinges and rollers of garage door.

2.Inspect the door for loose fasteners, worn or frayed counterbalance cables and the presences of legible safety labels/ tags. Have repairs made by a qualified service person.

Contact customer assistance for safety labels/ tags.

3.With door fully closed, move the emergency disconnect to the manual door operated position and manually operate door. If the door feels unbalanced or binds, have a qualified service person make necessary adjustments or repairs to the door.

4.Perform the contact/obstruction tests. See Steps 28 and 29 for the contact/obstruction test instructions. If Door/Opener fails Contact/Obstruction test run profile routine Steps 24 or 25 making sure door is completely closed prior to activation. If opener still fails, have a qualified service person make adjustments/repairs or this could result in severe or fatal injury.

5.Failure of Door/Opener to respond to transmitter or wall station may be due to a weak or dead battery. Replace the battery.

Battery replacement for Wall Station:

Remove the battery cover completely (right-hand side of wall station) by disengaging the battery cover’s lower clip. Install two

AAAbatteries into the wall station observing the polarity, (+) and (-), of both batteries. After a few seconds, the red LED will begin to blink every three seconds. If it is desired to slow the red LED blink rate refer to the wall station operation section on page 34 “Backlit LED Light”. Re-install the battery cover by first inserting its top into the wall station then inserting and securing its bottom.

Note: Use only 2 AAA batteries.

Battery replacement for Transmitter:

Insert a coin in the coin slot of the transmitter and twist coin to access the dead battery. Replace the battery, being careful to match the positive (+) symbols on the circuit boards with the battery.

Note: Use (1) CR2016 or equivalent battery.

Note: Dispose of dead battery properly.

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 38 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Copyright 2008 Wayne-Dalton Corp Rev 7 7/16/2008 Important NoticeIdrive mounts to Lift cables raise door Counterbalance above door From bottom Closed doorSecurity arm manually locks Package Contents Look for this symbol When Installing a NEW Door with AN IdrivePre-Installation InspectionEyes to Prevent Possible Severe or Fatal Injury Tools Needed System RequirementsWAYNE-DALTON Track Radius Photoelectric LOW Head 10,12,14,15Definition of key words used in this manual Table of ContentsSpring Tension Removal Retro-Fit InstallationDrum Wrap & End Bracket RemovalTorquemaster Plus End Bracket RemovalRemoval Center Bracket & Cable DrumRetro-Fit Installation End Bracket Removal RETRO-FIT TorquemasterVertical Track Height Adjustment Re-Install If NecessaryTop Bracket 8000/8100/8200 TrackTop Roller Adjustment RETRO-FIT InstallationsFailure to RE-ATTACH Horizontal Tracks to the Support Before Opening Door can Cause DoorAssembling Opener InstallationTorquemaster Installation Cable DrumsIdrive for Brackets End BracketsInstallation Idrive for Torquemaster InstallationCable Drum/ Drive Gear Counterbalance Springs End Bracket InstallationPositioning Support Bracket InstallationAttaching Opener To Support BracketPliers Attaching Disconnect CableSlack between opener and right end PliersMounting Disconnect Pilot drill lag screw location using 1/8 drill bitHandle Bracket 6ftAttaching Disconnect Handle Disconnect Handle UsageDisconnect Aligned and Seated Cable AdjustmentsSecuring Door For Spring WindingTools Needed Vice Clamps Hands Winding SpringsIMPORTANT! do not Overwind Springs Drum Wrap InstallationRecommended Spring Turns Tools Needed Step LadderIMPORTANT! do not Overwind Setting Spring TensionGarage Door Mounting Wall StationPRE-OPERATION Installing BatteryInstalling the Light Fixture Connecting Opener Power CordAttaching Diffuser Photoelectric Eyes are not For Proper AlignmentSensor Unit View of the Opener from the Front Sensor Wire InstallationSafety Sensor Alignment Securing the OpenerChecking for Obstructions Programming Light Fixture On when program button is pushedProfile Routine Standard Upper Limit On and remain on for 30 secondsProfile Routine Adjusting DetentCustom Upper Limit Work ProperlyOperation Lock Arm InstallationContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsDoor activation Read and Follow ALL InstructionsEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitOperation Custom pet position Customizing the SettingsMulti-Door Programming For more profile options go to page 28Maintenance Power Connection Permanent Wiring Option Reconnect PowerConfirm pot nut position* shown below OPENER, Using the Emergency Stations or Transmitters to OpenerProgramming Wireless WallProgramming Remote Controls Disconnect Handle Prior toSymptom Probable Cause Corrective Action TroubleshootingTroubleshootingoperation Lock Arm TroubleshootingDalton dealer or distributor Pre-drill 3/32 pilot hole Cut-Out Template to Aid InstallationDrill Template Pre-drill 5/64 pilot holePatent Information
Top Page Image Contents