Wayne-Dalton 3663-372 installation instructions Operation

Page 43

❉

Programming HomeLink® System to the Torquemaster® idrive® (Alternate)

 

NOTE: This Step can only be done on automobiles equipped with the HomeLink® system.

NOTE: Programming HomeLink® requires a Wayne-Dalton Transmitter that is programmed to the opener (the wallstation and transmitter(s) supplied with the opener, come pre-programmed from the factory). Any additional wallstation(s) or transmitter(s) will need to be programmed to the opener, see page 40.

IMPORTANT! Use the programming instructions provided with your vehicle first. Follow these instructions if the HomeLink® unit does not learn the transmitter, when using the vehicle’s instructions.

NOTE: Vehicle may need to be in accessory position when programming. Check car owner’s manual.

NOTE: HomeLink® is a registered trademark of Johnson Controls.

Programming/Training HomeLink® Unit

WARNING

GARAGE DOOR MAY OPERATE DURING PROGRAMMING. TO AVOID POSSIBLE SEVERE OR FATAL INJURY, PLACE THE EMERGENCY DISCONNECT HANDLE IN THE MANUAL OPERATED POSITION.

1.Pull the manual disconnect to put the opener in the disengaged position.

2.Press and hold the two outside buttons on the HomeLink®

unit until the HomeLink® light begins to flash rapidly (approx. 20 seconds), then release both buttons. (Do not perform this step to train additional hand-held transmitters.) NOTE: This operation erases all previously learned transmitters and that you need to re-teach any other transmitters to your HomeLink® unit by repeating steps 3 - 6 below.

3.Hold the end of the Wayne®Dalton hand-held transmitter approximately 1 to 3 inches away from the HomeLink® surface – keeping the HomeLink® indicator light in view.

4.Use the large button on the Wayne Dalton transmitter. Simultaneously press and hold desired Homelink® button and the Wayne Dalton transmitter large button. Continue to press both buttons counting LED flashes on the HomeLink® module; between 50 to 60 LED flashes the LED will either come on solid or do one “quick flash”; when either of these occur release both Wayne Dalton transmitter and HomeLink® buttons.

Teaching HomeLink® to the idrive® Opener

5.Press and release the red program button on the idrive® opener. The idrive® unit will beep, indicating that it is ready to learn.

NOTE: The idrive® will remain in the learn mode for 30 seconds.

6.Press the HomeLink® button used in Step 4 above for 1 to 3 seconds. The idrive® will beep indicating a successful learn.

7.Return the manual disconnect to the engaged position.

8.Press the HomeLink® button once more to operate the door.

NOTE: The first transmitter command after programming will only move the door through a six inch up/down cycle. Normal door operations will occur on the second use of the transmitter.

OPERATION

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 36 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Copyright 2008 Wayne-Dalton Corp Rev 7 7/16/2008 Important NoticeCounterbalance above door From bottom Closed door Idrive mounts to Lift cables raise doorSecurity arm manually locks Package Contents Look for this symbol When Installing a NEW Door with AN IdriveInspection Pre-InstallationEyes to Prevent Possible Severe or Fatal Injury 10,12,14,15 System RequirementsTools Needed WAYNE-DALTON Track Radius Photoelectric LOW HeadDefinition of key words used in this manual Table of ContentsRemoval Retro-Fit InstallationSpring Tension Removal Drum Wrap & End BracketCenter Bracket & Cable Drum End Bracket RemovalTorquemaster Plus RemovalRetro-Fit Installation End Bracket Removal RETRO-FIT Torquemaster8000/8100/8200 Track Re-Install If NecessaryVertical Track Height Adjustment Top BracketTracks to the Support Before Opening Door can Cause Door RETRO-FIT InstallationsTop Roller Adjustment Failure to RE-ATTACH HorizontalAssembling Opener InstallationCable Drums Torquemaster InstallationIdrive for Brackets End BracketsIdrive for Torquemaster Installation InstallationCable Drum/ Drive Gear Counterbalance Springs End Bracket InstallationSupport Bracket InstallationPositioning Support Bracket Attaching Opener ToPliers Attaching Disconnect CablePliers Slack between opener and right end6ft Pilot drill lag screw location using 1/8 drill bitMounting Disconnect Handle BracketDisconnect Handle Usage Attaching Disconnect HandleDisconnect Aligned and Seated Cable AdjustmentsFor Spring Winding Securing DoorTools Needed Vice Clamps Hands Winding SpringsTools Needed Step Ladder Drum Wrap InstallationIMPORTANT! do not Overwind Springs Recommended Spring TurnsIMPORTANT! do not Overwind Setting Spring TensionGarage Door Mounting Wall StationPRE-OPERATION Installing BatteryInstalling the Light Fixture Power Cord Connecting OpenerAttaching Diffuser For Proper Alignment Photoelectric Eyes are notSensor Unit View of the Opener from the Front Sensor Wire InstallationSecuring the Opener Safety Sensor AlignmentChecking for Obstructions On and remain on for 30 seconds On when program button is pushedProgramming Light Fixture Profile Routine Standard Upper LimitWork Properly Adjusting DetentProfile Routine Custom Upper LimitOperation Lock Arm InstallationContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsNever GO Under a STOPPED, Partially Open Door Read and Follow ALL InstructionsDoor activation Emergency DisconnectOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitOperation For more profile options go to page 28 Customizing the SettingsCustom pet position Multi-Door ProgrammingMaintenance Reconnect Power Power Connection Permanent Wiring OptionConfirm pot nut position* shown below Disconnect Handle Prior to Stations or Transmitters to OpenerProgramming Wireless WallOPENER, Using the Emergency Programming Remote ControlsSymptom Probable Cause Corrective Action TroubleshootingTroubleshootingoperation Lock Arm TroubleshootingDalton dealer or distributor Pre-drill 5/64 pilot hole Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Drill TemplatePatent Information
Top Page Image Contents