Wayne-Dalton 3663-372 installation instructions Operating the Wireless Wall Station

Page 41

❉

Operating the Wireless Wall Station

 

Up-Down Button:

Momentarily pressing the Up/Down button activates the door. If an out-of-balance condition causes the door to stop while opening or reverses the door while closing, apply constant pressure to the Up/Down button until the door is fully open or closed. This will allow the opener to move the door in an out of balance condition, until the problem is corrected (see Troubleshooting). The Up/Down button (when unit is closed) can be activated by pressing flip cover.

WARNING

THE SEVERE OUT-OF-BALANCE CONDITION MUST BE CORRECTED IMMEDIATELY. FAILURE TO MAKE ADJUSTMENTS/REPAIRS, COULD RESULT IN SEVERE OR FATAL INJURY.

Light Button:

Momentarily pressing the Light Button turns on the light fixture. The light fixture will remain on until either the Light Button is pressed again or the door is activated. The light fixture automatically turns on with a door activation and remains on for five minutes. Pressing the light fixture button before the five minutes has elapsed will turn off the light fixture. While the door is in motion, the Light Button functions identically as the Up/Down button, stopping or reversing the door immediately.

Timer Button:

Momentarily pressing the Timer Button causes a delayed activation of a stationary fully open door. The opener will signal seven beeps (approx.

8 seconds) then beep constantly for two seconds prior to closing the door, allowing time to exit the garage when the opener is in the timer mode. Pressing any button, except for the profile button while the opener is beeping cancels the timer mode.

NOTE: The Timer feature will only function with the door in the full open position. Pressing the Timer Button with a stationary door in any other position will cause the opener to beep four times and the door will not be activated.

While the door is in motion, the Timer Button functions identically as the Up/Down button, stopping or reversing the door immediately.

Slide Switch:

The Slide Switch has two positions: Normal, and Door lock.

Normal position:

Move the Slide Switch to normal position for all normal functions of the opener. The normal position will cancel the door lock feature.

NOTE: When the Slide Switch is moved to the unlocked position the opener will beep once.

Door Lock position:

If the door is stopped (fully open, fully closed or partially open) move the Slide Switch to the door lock position to suspend all normal functions of the opener. The opener will remain completely disabled and non-operational in this mode. All wall stations, transmitters and keyless entry units are ignored until the Slide Switch is moved to the normal position. If the door is moving when the Slide Switch is moved to the door lock position, the door lock mode is not activated and all functions of the opener remain active.

NOTE: When the Slide Switch is moved to the locked position the opener will beep twice.

Backlit LED Light:

The red LED blinks intermittently to help you locate the wall station in a dark garage. This blink rate can be changed for longer battery life or can be turned off. The default blink rate is one blink every 3 seconds. For longer battery life the blink rate can be changed to blink once every 6 seconds. To change the blink rate, remove the battery cover and remove one battery. Re-install the battery and within 2 seconds, press the Light button. Re-install the battery cover.

For longest battery life, the blink can be turned off. To turn off the blink, remove the battery cover and remove one battery.

Re-install the battery and within 2 seconds, press the pet button. Re-install the battery cover.

NOTE: The wall stations red LED will light while any wall station button remains pressed.

Pet Position:

Pressing the Pet button opens a closed door to a preset position between eight and thirty inches above the floor, allowing pets to enter and exit the garage without the door being fully open. The door must be fully closed to activate the pet open feature. Pressing the Pet button with a stationary door in the pet open position will cause the door to close. Pressing the Up/Down button while the door is in the pet position will cause the door to open. While the door is in motion, the pet button functions identically to the Up/Down button, stopping or reversing the door immediately. The pet feature allows for custom setting of the pet position door height. See Customizing the Settings on page 37.

NOTE: A door in the “pet position” (open 8-30 inches) is not locked and should not be used as a secured door position.

Profile Routine:

Press and hold the Profile button for 5 seconds to initiate the “Profile Routine”. See Customizing the Settings on page 37.

NOTE: The wall stations red LED will light while any wall station button remains pressed. See Maintenance section for battery replacement.

Light Button

Up/Down Button

Slide Switch

Timer Button

Profile Button

OPERATION

Pet Button

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 34 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Copyright 2008 Wayne-Dalton Corp Rev 7 7/16/2008 Important NoticeSecurity arm manually locks Idrive mounts to Lift cables raise doorCounterbalance above door From bottom Closed door Package Contents Look for this symbol When Installing a NEW Door with AN IdriveEyes to Prevent Possible Severe or Fatal Injury Pre-InstallationInspection Tools Needed System RequirementsWAYNE-DALTON Track Radius Photoelectric LOW Head 10,12,14,15Definition of key words used in this manual Table of ContentsSpring Tension Removal Retro-Fit InstallationDrum Wrap & End Bracket RemovalTorquemaster Plus End Bracket RemovalRemoval Center Bracket & Cable DrumRetro-Fit Installation End Bracket Removal RETRO-FIT TorquemasterVertical Track Height Adjustment Re-Install If NecessaryTop Bracket 8000/8100/8200 TrackTop Roller Adjustment RETRO-FIT InstallationsFailure to RE-ATTACH Horizontal Tracks to the Support Before Opening Door can Cause DoorAssembling Opener InstallationIdrive for Torquemaster InstallationCable Drums Brackets End BracketsCable Drum/ Drive Gear InstallationIdrive for Torquemaster Installation Counterbalance Springs End Bracket InstallationPositioning Support Bracket InstallationAttaching Opener To Support BracketPliers Attaching Disconnect CableSlack between opener and right end PliersMounting Disconnect Pilot drill lag screw location using 1/8 drill bitHandle Bracket 6ftDisconnect Attaching Disconnect HandleDisconnect Handle Usage Aligned and Seated Cable AdjustmentsTools Needed Vice Clamps Securing DoorFor Spring Winding Hands Winding SpringsIMPORTANT! do not Overwind Springs Drum Wrap InstallationRecommended Spring Turns Tools Needed Step LadderIMPORTANT! do not Overwind Setting Spring TensionGarage Door Mounting Wall StationPRE-OPERATION Installing BatteryInstalling the Light Fixture Attaching Diffuser Connecting OpenerPower Cord Sensor Unit Photoelectric Eyes are notFor Proper Alignment View of the Opener from the Front Sensor Wire InstallationChecking for Obstructions Safety Sensor AlignmentSecuring the Opener Programming Light Fixture On when program button is pushedProfile Routine Standard Upper Limit On and remain on for 30 secondsProfile Routine Adjusting DetentCustom Upper Limit Work ProperlyOperation Lock Arm InstallationContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsDoor activation Read and Follow ALL InstructionsEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitOperation Custom pet position Customizing the SettingsMulti-Door Programming For more profile options go to page 28Maintenance Confirm pot nut position* shown below Power Connection Permanent Wiring OptionReconnect Power OPENER, Using the Emergency Stations or Transmitters to OpenerProgramming Wireless WallProgramming Remote Controls Disconnect Handle Prior toSymptom Probable Cause Corrective Action TroubleshootingTroubleshootingoperation Lock Arm TroubleshootingDalton dealer or distributor Pre-drill 3/32 pilot hole Cut-Out Template to Aid InstallationDrill Template Pre-drill 5/64 pilot holePatent Information
Top Page Image Contents