Wayne-Dalton 3663-372 Top Bracket, Re-Install If Necessary, 8000/8100/8200 Track

Page 12

R5

9100 Top Bracket

 

 

Re-Install (If Necessary)

 

If installing an idrive® opener on an installed

Tools Needed:

Power Drill

9100 door, the top bracket and roller

location will have to be adjusted for the

 

7/16" Socket

opener to work properly.

Driver

Loosen the (2) 1/4”-20 nuts from the top

Step Ladder

bracket slide.

 

Remove the (4) 1/4”-14 x 5/8" self-tapping

 

screws from the top bracket.

 

Raise the top bracket to align the bottom

 

slots with the second set of holes in the

 

end cap.

 

Re-attach top bracket to the end cap with

 

the (4) 1/4”-14 x 5/8" self-tapping screws.

 

Re-align the top roller in the horizontal track

 

by moving the top bracket slide out to force

 

the door section against the weather seal.

 

Tighten (2) 1/4”-20 Nuts.

 

Repeat for the opposite side.

 

 

1/4” - 20

Top

 

Carriage Bolts

Bracket

 

and Nuts

Slide

 

 

Horizontal

 

 

Track

 

1/4”- 14 x 5/8”

 

 

Self-Tapping

 

 

Screws

 

 

 

Top

 

 

Roller

 

End Cap

Top

 

a

b

Bracket

NOTE: The 9100 doors have a painted steel face, foam insulation and white paper backing. If your door does not match this description you may skip this step.

CAUTION: TO AVOID THE TOP PANEL FROM FALLING, COMPLETE RE- INSTALLATION ON ONE SIDE BEFORE BEGINNING THE OTHER.

R6

8000/8100/8200 Track

Vertical Track Height Adjustment

(If Required)

Tools Needed:

NOTE: The door must be in the fully closed

position.

Power Drill

If installing an idrive® opener on an

7/16" Socket

8000/8100/8200 door, the top roller location

Drive

and track height will have to be modified for

 

Pencil

the opener to work properly. Perform the

Tape Measure

following steps:

 

Step Ladder

NOTE: The bottom edge of the track needs to

be spaced 1” above the floor. If the track is

 

 

already spaced off the floor 1”, skip this step.

 

Fasten a nail in the door jamb, between the

Flagangle

Remove

Lag Screws

Flange Nut

Nail

Top Bracket Slide

door and the track at the ends of each

section. Bend the nail over each section to

hold them in place.

Remove the lag screws from the flagangle and

each jamb bracket. Using a 7/16" socket

driver, loosen the flange nut on the Top

bracket slide. Place a mark 1" up from one of

the tops of one of the jamb brackets. Raise

the track up and align the jamb bracket with

this line. With the track relocated, re-attach

the flagangle, end bracket, and jamb brackets

to the header and/or door jamb. Make certain

to maintain spacing between edge of door and

vertical track.

NOTE: Pilot drill all lag screw locations.

Track

Nail

Nail

Jamb

Bracket

Nail

Nail Placement

Nail bent over door section

Track

(Door Section)

5Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 12
Contents Important Notice Copyright 2008 Wayne-Dalton Corp Rev 7 7/16/2008Idrive mounts to Lift cables raise door Counterbalance above door From bottom Closed doorSecurity arm manually locks Package Contents When Installing a NEW Door with AN Idrive Look for this symbolPre-Installation InspectionEyes to Prevent Possible Severe or Fatal Injury System Requirements Tools NeededWAYNE-DALTON Track Radius Photoelectric LOW Head 10,12,14,15Table of Contents Definition of key words used in this manualRetro-Fit Installation Spring Tension RemovalDrum Wrap & End Bracket RemovalEnd Bracket Removal Torquemaster PlusRemoval Center Bracket & Cable DrumRetro-Fit Installation RETRO-FIT Torquemaster End Bracket RemovalRe-Install If Necessary Vertical Track Height AdjustmentTop Bracket 8000/8100/8200 TrackRETRO-FIT Installations Top Roller AdjustmentFailure to RE-ATTACH Horizontal Tracks to the Support Before Opening Door can Cause DoorInstallation Assembling OpenerTorquemaster Installation Cable DrumsIdrive for End Brackets BracketsInstallation Idrive for Torquemaster InstallationCable Drum/ Drive Gear End Bracket Installation Counterbalance SpringsInstallation Positioning Support BracketAttaching Opener To Support BracketAttaching Disconnect Cable PliersSlack between opener and right end PliersPilot drill lag screw location using 1/8 drill bit Mounting DisconnectHandle Bracket 6ftAttaching Disconnect Handle Disconnect Handle UsageDisconnect Cable Adjustments Aligned and SeatedSecuring Door For Spring WindingTools Needed Vice Clamps Winding Springs HandsDrum Wrap Installation IMPORTANT! do not Overwind SpringsRecommended Spring Turns Tools Needed Step LadderSetting Spring Tension IMPORTANT! do not OverwindMounting Wall Station Garage DoorInstalling Battery PRE-OPERATIONInstalling the Light Fixture Connecting Opener Power CordAttaching Diffuser Photoelectric Eyes are not For Proper AlignmentSensor Unit Sensor Wire Installation View of the Opener from the FrontSafety Sensor Alignment Securing the OpenerChecking for Obstructions On when program button is pushed Programming Light FixtureProfile Routine Standard Upper Limit On and remain on for 30 secondsAdjusting Detent Profile RoutineCustom Upper Limit Work ProperlyLock Arm Installation OperationLock Arm Installation Contact Obstruction TestTesting the Safety Sensors Fatal Injury MAY ResultRead and Follow ALL Instructions Door activationEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Programming/Training HomeLink Unit Teaching HomeLink to the idrive openerOperation Customizing the Settings Custom pet positionMulti-Door Programming For more profile options go to page 28Maintenance Power Connection Permanent Wiring Option Reconnect PowerConfirm pot nut position* shown below Stations or Transmitters to OpenerProgramming Wireless Wall OPENER, Using the EmergencyProgramming Remote Controls Disconnect Handle Prior toTroubleshooting Symptom Probable Cause Corrective ActionLock Arm Troubleshooting TroubleshootingoperationDalton dealer or distributor Cut-Out Template to Aid Installation Pre-drill 3/32 pilot holeDrill Template Pre-drill 5/64 pilot holePatent Information