Wayne-Dalton 3663-372 Programming Light Fixture, Profile Routine Standard Upper Limit

Page 35

	23	Programming Light Fixture
		Programming Light Fixture

	Tools Needed:	Press the red program button on the light
	Step Ladder	fixture. The LED on the light fixture will turn
	Step Ladder	on and remain on for 30 seconds
		on and remain on for 30 seconds
		or until a opener is learned to the light
		fixture. The incandescent lamp will also turn
		on when program button is pushed.
		Press the light button on the wall station.
		This must be done within 30 seconds of
		pressing the program button on the light
		fixture. The light fixture lamp and LED will
		blink three times to indicate successful
		programming. The light fixture can now be
		turned on and off from this wall station.
		NOTE: In order to program the opener to
		the light fixture, the installer must have the
		wall station already programmed to the
		opener.

Program Button LED

Light Button

per
O	at
o	e
T	D
Press
	o
	o
	Here	r
		r

24

Tools Needed:

None

Profile Routine

(Standard Upper Limit)

WARNING

TO AVOID INJURY, NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!

The profile routine automatically sets the door open and close limits and calibrates obstruction sensing. During the profile routine, the door will move up and down twice.

NOTE: If an object such as a ceiling beam obstructs the door from opening completely, skip this step. Set a Custom Upper Limit, see Step 25.

NOTE: The door must be in its fully closed position and the disconnect handle must be in the motor operated position (upper position) to initiate the profile routine.

NOTE: Profile routine will not run if safety sensors are not aligned (only if required installation).

Press and hold the profile button for five (5) seconds. The opener will beep twice, release the profile button, indicating the activation of the profile routine. The door will now move to the fully open position and stop, beep twice and then the door will close completely.

Next, the door will go through one more up/ down cycle. Once this is complete, the door limits are set and the profile is complete.

NOTE: Upon successful completion proceed to Step 26.

Profile Button

PRE-OPERATION

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 28 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 35

Contents Copyright 2008 Wayne-Dalton Corp Rev 7 7/16/2008 Important NoticeSecurity arm manually locks Idrive mounts to Lift cables raise doorCounterbalance above door From bottom Closed door Package Contents Look for this symbol When Installing a NEW Door with AN IdriveEyes to Prevent Possible Severe or Fatal Injury Pre-InstallationInspection 10,12,14,15 System RequirementsTools Needed WAYNE-DALTON Track Radius Photoelectric LOW HeadDeﬁnition of key words used in this manual Table of ContentsRemoval Retro-Fit InstallationSpring Tension Removal Drum Wrap & End BracketCenter Bracket & Cable Drum End Bracket RemovalTorquemaster Plus RemovalRetro-Fit Installation End Bracket Removal RETRO-FIT Torquemaster8000/8100/8200 Track Re-Install If NecessaryVertical Track Height Adjustment Top BracketTracks to the Support Before Opening Door can Cause Door RETRO-FIT InstallationsTop Roller Adjustment Failure to RE-ATTACH HorizontalAssembling Opener InstallationIdrive for Torquemaster InstallationCable Drums Brackets End BracketsCable Drum/ Drive Gear InstallationIdrive for Torquemaster Installation Counterbalance Springs End Bracket InstallationSupport Bracket InstallationPositioning Support Bracket Attaching Opener ToPliers Attaching Disconnect CablePliers Slack between opener and right end6ft Pilot drill lag screw location using 1/8 drill bitMounting Disconnect Handle BracketDisconnect Attaching Disconnect HandleDisconnect Handle Usage Aligned and Seated Cable AdjustmentsTools Needed Vice Clamps Securing DoorFor Spring Winding Hands Winding SpringsTools Needed Step Ladder Drum Wrap InstallationIMPORTANT! do not Overwind Springs Recommended Spring TurnsIMPORTANT! do not Overwind Setting Spring TensionGarage Door Mounting Wall StationPRE-OPERATION Installing BatteryInstalling the Light Fixture Attaching Diffuser Connecting OpenerPower Cord Sensor Unit Photoelectric Eyes are notFor Proper Alignment View of the Opener from the Front Sensor Wire InstallationChecking for Obstructions Safety Sensor AlignmentSecuring the Opener On and remain on for 30 seconds On when program button is pushedProgramming Light Fixture Profile Routine Standard Upper LimitWork Properly Adjusting DetentProfile Routine Custom Upper LimitOperation Lock Arm InstallationContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsNever GO Under a STOPPED, Partially Open Door Read and Follow ALL InstructionsDoor activation Emergency DisconnectOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitOperation For more profile options go to page 28 Customizing the SettingsCustom pet position Multi-Door ProgrammingMaintenance Confirm pot nut position* shown below Power Connection Permanent Wiring OptionReconnect Power Disconnect Handle Prior to Stations or Transmitters to OpenerProgramming Wireless WallOPENER, Using the Emergency Programming Remote ControlsSymptom Probable Cause Corrective Action TroubleshootingTroubleshootingoperation Lock Arm TroubleshootingDalton dealer or distributor Pre-drill 5/64 pilot hole Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Drill TemplatePatent Information