Wayne-Dalton 3663-372 installation instructions Patent Information

Page 52

Patent Information

Models: 3663-372

Made under the following US patents and methods D413,579; D466,141; D472,568; D472,910; D473,573; D473,574; D474,215; D505,393; D517,580; CA 2,348,784; 5,929,580; 6,078,249; 6,145,570; 6,164,014; 6,253,824; 6,263,947; 6,325,134; 6,326,751; 6,326,754; 6,401,792; 6,561,255; 6,561,256; 6,568,454; 6,588,156; 6,605,910; 6,667,591; 6,739,372; 6,845,804; 6,851,465; 6,873,127; 6,880,609; 6,903,650; 7,053,571; 7,061,197; 7,075,256; 7,109,677; 7,123,128; 7,143,804; 7,173,389; 7,173,514; 7,173,516; 7,183,732; 7,190,266; 7,193,502; 7,207,142; 7,211,975; 7,246,647; 7,280,031; 7,327,107; 7,327,108; 7,327,249; 7,358,480; 7,367,160; 7,375,484; 7,375,612; 7,376,401;7,397,342. Other US and Foreign Patents pending.

FCC and IC Statement

FCC Regulatory Information:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IC Regulatory Information:

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

NOTE: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communication; however, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning equipment off and on, user is encouraged to try to correct interference by one or more of the following measures: Reorient or relocate receiving antenna. Increase separation between equipment and receiver. Connect equipment into an outlet on a circuit different from that which receiver is connected. Consult your dealer or/and experienced radio/ television technician for help.

WARNING: Changes or modifications to this unit not expressly approved by party responsible for compliance could void user’s authority to operate this equipment.

Image 52
Contents Important Notice Copyright 2008 Wayne-Dalton Corp Rev 7 7/16/2008Counterbalance above door From bottom Closed door Idrive mounts to Lift cables raise doorSecurity arm manually locks Package Contents When Installing a NEW Door with AN Idrive Look for this symbolInspection Pre-InstallationEyes to Prevent Possible Severe or Fatal Injury System Requirements Tools NeededWAYNE-DALTON Track Radius Photoelectric LOW Head 10,12,14,15Table of Contents Definition of key words used in this manualRetro-Fit Installation Spring Tension RemovalDrum Wrap & End Bracket RemovalEnd Bracket Removal Torquemaster PlusRemoval Center Bracket & Cable DrumRetro-Fit Installation RETRO-FIT Torquemaster End Bracket RemovalRe-Install If Necessary Vertical Track Height AdjustmentTop Bracket 8000/8100/8200 TrackRETRO-FIT Installations Top Roller AdjustmentFailure to RE-ATTACH Horizontal Tracks to the Support Before Opening Door can Cause DoorInstallation Assembling OpenerCable Drums Torquemaster InstallationIdrive for End Brackets BracketsIdrive for Torquemaster Installation InstallationCable Drum/ Drive Gear End Bracket Installation Counterbalance SpringsInstallation Positioning Support BracketAttaching Opener To Support BracketAttaching Disconnect Cable PliersSlack between opener and right end PliersPilot drill lag screw location using 1/8 drill bit Mounting DisconnectHandle Bracket 6ftDisconnect Handle Usage Attaching Disconnect HandleDisconnect Cable Adjustments Aligned and SeatedFor Spring Winding Securing DoorTools Needed Vice Clamps Winding Springs HandsDrum Wrap Installation IMPORTANT! do not Overwind SpringsRecommended Spring Turns Tools Needed Step LadderSetting Spring Tension IMPORTANT! do not OverwindMounting Wall Station Garage DoorInstalling Battery PRE-OPERATIONInstalling the Light Fixture Power Cord Connecting OpenerAttaching Diffuser For Proper Alignment Photoelectric Eyes are notSensor Unit Sensor Wire Installation View of the Opener from the FrontSecuring the Opener Safety Sensor AlignmentChecking for Obstructions On when program button is pushed Programming Light FixtureProfile Routine Standard Upper Limit On and remain on for 30 secondsAdjusting Detent Profile RoutineCustom Upper Limit Work ProperlyLock Arm Installation OperationLock Arm Installation Contact Obstruction TestTesting the Safety Sensors Fatal Injury MAY ResultRead and Follow ALL Instructions Door activationEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Programming/Training HomeLink Unit Teaching HomeLink to the idrive openerOperation Customizing the Settings Custom pet positionMulti-Door Programming For more profile options go to page 28Maintenance Reconnect Power Power Connection Permanent Wiring OptionConfirm pot nut position* shown below Stations or Transmitters to OpenerProgramming Wireless Wall OPENER, Using the EmergencyProgramming Remote Controls Disconnect Handle Prior toTroubleshooting Symptom Probable Cause Corrective ActionLock Arm Troubleshooting TroubleshootingoperationDalton dealer or distributor Cut-Out Template to Aid Installation Pre-drill 3/32 pilot holeDrill Template Pre-drill 5/64 pilot holePatent Information