Wayne-Dalton 3663-372 Pre-drill 3/32 pilot hole, Drill Template, Pre-drill 5/64 pilot hole

Page 51

✁	Cut-Out Template to Aid Installation

Pre-drill 3/32” pilot hole

Pre-drill 5/64” pilot hole

Wall Station Template

Keyless Entry Template

Please Do Not Return This Product To The Store

Call Us Toll-Free:

Call Us Directly! Our Trained Technicians Will Answer(888) 827-3667Your Questions and /or Ship Any Parts You May Need

Thank you for your purchase

www.wayne-dalton.com

DRILL TEMPLATE

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 44 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 51

Contents Copyright 2008 Wayne-Dalton Corp Rev 7 7/16/2008 Important NoticeIdrive mounts to Lift cables raise door Counterbalance above door From bottom Closed doorSecurity arm manually locks Package Contents Look for this symbol When Installing a NEW Door with AN IdrivePre-Installation InspectionEyes to Prevent Possible Severe or Fatal Injury 10,12,14,15 System RequirementsTools Needed WAYNE-DALTON Track Radius Photoelectric LOW HeadDeﬁnition of key words used in this manual Table of ContentsRemoval Retro-Fit InstallationSpring Tension Removal Drum Wrap & End BracketCenter Bracket & Cable Drum End Bracket RemovalTorquemaster Plus RemovalRetro-Fit Installation End Bracket Removal RETRO-FIT Torquemaster8000/8100/8200 Track Re-Install If NecessaryVertical Track Height Adjustment Top BracketTracks to the Support Before Opening Door can Cause Door RETRO-FIT InstallationsTop Roller Adjustment Failure to RE-ATTACH HorizontalAssembling Opener InstallationTorquemaster Installation Cable DrumsIdrive for Brackets End BracketsInstallation Idrive for Torquemaster InstallationCable Drum/ Drive Gear Counterbalance Springs End Bracket InstallationSupport Bracket InstallationPositioning Support Bracket Attaching Opener ToPliers Attaching Disconnect CablePliers Slack between opener and right end6ft Pilot drill lag screw location using 1/8 drill bitMounting Disconnect Handle BracketAttaching Disconnect Handle Disconnect Handle UsageDisconnect Aligned and Seated Cable AdjustmentsSecuring Door For Spring WindingTools Needed Vice Clamps Hands Winding SpringsTools Needed Step Ladder Drum Wrap InstallationIMPORTANT! do not Overwind Springs Recommended Spring TurnsIMPORTANT! do not Overwind Setting Spring TensionGarage Door Mounting Wall StationPRE-OPERATION Installing BatteryInstalling the Light Fixture Connecting Opener Power CordAttaching Diffuser Photoelectric Eyes are not For Proper AlignmentSensor Unit View of the Opener from the Front Sensor Wire InstallationSafety Sensor Alignment Securing the OpenerChecking for Obstructions On and remain on for 30 seconds On when program button is pushedProgramming Light Fixture Profile Routine Standard Upper LimitWork Properly Adjusting DetentProfile Routine Custom Upper LimitOperation Lock Arm InstallationContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsNever GO Under a STOPPED, Partially Open Door Read and Follow ALL InstructionsDoor activation Emergency DisconnectOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitOperation For more profile options go to page 28 Customizing the SettingsCustom pet position Multi-Door ProgrammingMaintenance Power Connection Permanent Wiring Option Reconnect PowerConfirm pot nut position* shown below Disconnect Handle Prior to Stations or Transmitters to OpenerProgramming Wireless WallOPENER, Using the Emergency Programming Remote ControlsSymptom Probable Cause Corrective Action TroubleshootingTroubleshootingoperation Lock Arm TroubleshootingDalton dealer or distributor Pre-drill 5/64 pilot hole Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Drill TemplatePatent Information