Wayne-Dalton 3663-372 installation instructions Pre-Installation, Inspection

Page 5

PRE-INSTALLATION INSPECTION

CAUTION! Do not install this opener on your door unless the following requirements are met.

Electrical outlet on

Electrical outlet on the

A

the ceiling is for

wall is for opener

 

light/opener

 

 

Mounting Surface

C

Torquemaster® Plus

Torquemaster®

 

B 1” Clearance for Motor

Torque Tube

 

 

End Bracket

Top of

Door

 

 

 

 

 

 

 

 

 

 

 

Pre-Installation

 

 

WARNING

PHOTOELECTRIC EYES ARE NOT REQUIRED ON WAYNE-DALTON

 

 

 

 

 

SERIES 9000 AND MODEL 5120 AND 5140 DOORS. ALL OTHER

 

 

 

Inspection

 

DOORS, WHICH DO NOT

HAVE PINCH-RESISTANT SECTION JOINTS, REQUIRE PHOTOELECTRIC

 

 

 

 

EYES TO PREVENT POSSIBLE SEVERE OR FATAL INJURY.

 

 

CAUTION: DO NOT INSTALL THIS OPENER ON YOUR DOOR UNLESS THE FOLLOWING REQUIREMENTS ARE MET.

 

 

 

 

 

USE THE ILLUSTRATION ABOVE AS A VISUAL AID.

 

 

A. You must have a Wayne-Dalton Torquemaster® or Torquemaster®

D. Your door must not exceed 8' in height.

 

Plus counterbalance system to install this opener (see A above).

E. The idrive® opener will only work on sectional doors. Do not

 

 

 

 

 

 

 

 

B. The motor requires 1" of clearance above the top of the end

install on one-piece doors.

 

bracket for Torquemaster and 1-1/4” of clearance above the top

F. Your garage door must be properly balanced (door must not be

 

of the end bracket for Torquemaster plus.

 

heavy to lift, nor lift by itself).

 

 

 

 

 

 

 

 

C. Two electrical outlets are recommended for the idrive®

G. Horizontal tracks should be raised 1" above level at rear of Track.

 

installation. One of these outlets needs to be located less than 6'

 

H. We do not recommend installing the idrive® opener on

 

from the opener. The second outlet, for the light, can be located

 

at a position of your choice.

 

 

 

Model 9700 door widths of 16’ - 18’.

 

If, in the event that an electrical outlet is not located within 6' of

I. Maximum door weight (without spring tension) must not

 

the opener, contact a local electrician for further options. As a

exceed 304 lb.

 

convenience, an electrical outlet is provided on the light fixture.

 

 

The 6’ opener cord can be used with this outlet.

 

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. III You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Copyright 2008 Wayne-Dalton Corp Rev 7 7/16/2008 Important NoticeSecurity arm manually locks Idrive mounts to Lift cables raise doorCounterbalance above door From bottom Closed door Package Contents Look for this symbol When Installing a NEW Door with AN IdriveEyes to Prevent Possible Severe or Fatal Injury Pre-InstallationInspection Tools Needed System RequirementsWAYNE-DALTON Track Radius Photoelectric LOW Head 10,12,14,15Definition of key words used in this manual Table of ContentsSpring Tension Removal Retro-Fit InstallationDrum Wrap & End Bracket RemovalTorquemaster Plus End Bracket RemovalRemoval Center Bracket & Cable DrumRetro-Fit Installation End Bracket Removal RETRO-FIT TorquemasterVertical Track Height Adjustment Re-Install If NecessaryTop Bracket 8000/8100/8200 TrackTop Roller Adjustment RETRO-FIT InstallationsFailure to RE-ATTACH Horizontal Tracks to the Support Before Opening Door can Cause DoorAssembling Opener InstallationIdrive for Torquemaster InstallationCable Drums Brackets End BracketsCable Drum/ Drive Gear InstallationIdrive for Torquemaster Installation Counterbalance Springs End Bracket InstallationPositioning Support Bracket InstallationAttaching Opener To Support BracketPliers Attaching Disconnect CableSlack between opener and right end PliersMounting Disconnect Pilot drill lag screw location using 1/8 drill bitHandle Bracket 6ftDisconnect Attaching Disconnect HandleDisconnect Handle Usage Aligned and Seated Cable AdjustmentsTools Needed Vice Clamps Securing DoorFor Spring Winding Hands Winding SpringsIMPORTANT! do not Overwind Springs Drum Wrap InstallationRecommended Spring Turns Tools Needed Step LadderIMPORTANT! do not Overwind Setting Spring TensionGarage Door Mounting Wall StationPRE-OPERATION Installing BatteryInstalling the Light Fixture Attaching Diffuser Connecting OpenerPower Cord Sensor Unit Photoelectric Eyes are notFor Proper Alignment View of the Opener from the Front Sensor Wire InstallationChecking for Obstructions Safety Sensor AlignmentSecuring the Opener Programming Light Fixture On when program button is pushedProfile Routine Standard Upper Limit On and remain on for 30 secondsProfile Routine Adjusting DetentCustom Upper Limit Work ProperlyOperation Lock Arm InstallationContact Obstruction Test Lock Arm InstallationFatal Injury MAY Result Testing the Safety SensorsDoor activation Read and Follow ALL InstructionsEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink UnitOperation Custom pet position Customizing the SettingsMulti-Door Programming For more profile options go to page 28Maintenance Confirm pot nut position* shown below Power Connection Permanent Wiring OptionReconnect Power OPENER, Using the Emergency Stations or Transmitters to OpenerProgramming Wireless WallProgramming Remote Controls Disconnect Handle Prior toSymptom Probable Cause Corrective Action TroubleshootingTroubleshootingoperation Lock Arm TroubleshootingDalton dealer or distributor Pre-drill 3/32 pilot hole Cut-Out Template to Aid InstallationDrill Template Pre-drill 5/64 pilot holePatent Information
Top Page Image Contents