Wayne-Dalton 3663-372 Securing Door, For Spring Winding, Tools Needed Vice Clamps

Page 24

11

Securing Door

 

 

for Spring Winding

 

 

Tools Needed:

(2) Vice Clamps

Place vice clamps onto both vertical tracks just above the third roller. This is to prevent the garage door from raising while winding the springs.

WARNING

FAILURE TO CLAMP TRACK CAN ALLOW DOOR TO RAISE UNEXPECTEDLY, RESULTING IN SEVERE OR FATAL INJURY.

PLACE VICE CLAMPS

ABOVE 3RD ROLLER

TRACK

VICE CLAMPS ATTACHED

TO INNER

RAIL OF TRACK

17Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 24
Contents Important Notice Copyright 2008 Wayne-Dalton Corp Rev 7 7/16/2008Idrive mounts to Lift cables raise door Counterbalance above door From bottom Closed doorSecurity arm manually locks Package Contents When Installing a NEW Door with AN Idrive Look for this symbolPre-Installation InspectionEyes to Prevent Possible Severe or Fatal Injury System Requirements Tools NeededWAYNE-DALTON Track Radius Photoelectric LOW Head 10,12,14,15Table of Contents Definition of key words used in this manualRetro-Fit Installation Spring Tension RemovalDrum Wrap & End Bracket RemovalEnd Bracket Removal Torquemaster PlusRemoval Center Bracket & Cable DrumRetro-Fit Installation RETRO-FIT Torquemaster End Bracket RemovalRe-Install If Necessary Vertical Track Height AdjustmentTop Bracket 8000/8100/8200 TrackRETRO-FIT Installations Top Roller AdjustmentFailure to RE-ATTACH Horizontal Tracks to the Support Before Opening Door can Cause DoorInstallation Assembling OpenerTorquemaster Installation Cable DrumsIdrive for End Brackets BracketsInstallation Idrive for Torquemaster InstallationCable Drum/ Drive Gear End Bracket Installation Counterbalance SpringsInstallation Positioning Support BracketAttaching Opener To Support BracketAttaching Disconnect Cable PliersSlack between opener and right end PliersPilot drill lag screw location using 1/8 drill bit Mounting DisconnectHandle Bracket 6ftAttaching Disconnect Handle Disconnect Handle UsageDisconnect Cable Adjustments Aligned and SeatedSecuring Door For Spring WindingTools Needed Vice Clamps Winding Springs HandsDrum Wrap Installation IMPORTANT! do not Overwind SpringsRecommended Spring Turns Tools Needed Step LadderSetting Spring Tension IMPORTANT! do not OverwindMounting Wall Station Garage DoorInstalling Battery PRE-OPERATIONInstalling the Light Fixture Connecting Opener Power CordAttaching Diffuser Photoelectric Eyes are not For Proper AlignmentSensor Unit Sensor Wire Installation View of the Opener from the FrontSafety Sensor Alignment Securing the OpenerChecking for Obstructions On when program button is pushed Programming Light FixtureProfile Routine Standard Upper Limit On and remain on for 30 secondsAdjusting Detent Profile RoutineCustom Upper Limit Work ProperlyLock Arm Installation OperationLock Arm Installation Contact Obstruction TestTesting the Safety Sensors Fatal Injury MAY ResultRead and Follow ALL Instructions Door activationEmergency Disconnect Never GO Under a STOPPED, Partially Open DoorOperating the Wireless Wall Station Programming/Training HomeLink Unit Teaching HomeLink to the idrive openerOperation Customizing the Settings Custom pet positionMulti-Door Programming For more profile options go to page 28Maintenance Power Connection Permanent Wiring Option Reconnect PowerConfirm pot nut position* shown below Stations or Transmitters to OpenerProgramming Wireless Wall OPENER, Using the EmergencyProgramming Remote Controls Disconnect Handle Prior toTroubleshooting Symptom Probable Cause Corrective ActionLock Arm Troubleshooting TroubleshootingoperationDalton dealer or distributor Cut-Out Template to Aid Installation Pre-drill 3/32 pilot holeDrill Template Pre-drill 5/64 pilot holePatent Information