SPECIFICATIONS
TPBS013/1199
GRAVIMETRIC BATCH BLENDERS AutoWeigh GB900 Series Models
C
C
C
D | GB920 | C | |
2 | 1 | ||
A |
|
| B |
|
| B |
|
D |
| GB940 | C |
|
| 4 |
|
2 |
|
| 1 |
|
| 3 |
|
A |
| B | B |
|
|
| |
D |
| GB960 | C |
|
|
| |
8 |
| 7 | 4 |
1 |
| 2 | 3 |
A |
|
| B |
|
|
| |
|
| B |
|
FEEDER LOCATIONS
NOTE: Any one of the feeders (A,B,C or D)can be designated position 5 or 6.
B
A
FRONT VIEW
GB920
C
A
SIDE VIEW
GB920/GB940
B
C
FRONT VIEW | SIDE VIEW |
GB940/GB960 | GB960 |
MODELS |
| GB920 | GB940 | GB960 | |
Performance characteristics |
|
|
|
| |
Batch size lbs {g} |
| 19.8 {9000} | 19.8 {9000} | 19.8 {9000} | |
Maximum throughput lbs/hr {kg/hr}* | 5200 {2359} | 3300 {1497} | 2124 {965} | ||
Bin capacity - main ingredient | ft3 {liter} | 8.5 {240.7} | 6.7 {189.7} | 3.6 {102.9} | |
Bin capacity - minor ingredient | ft3 {liter} | NA | 3.6 {107.6} | 3.6 {107.6} | |
Maximum number of materials |
| 6 | 8 | 10 | |
Number of discharge valves |
| 2 | 4 | 6 | |
Number of additive feeders |
| up to 4 | up to 4 | up to 4 | |
Control software (# of components) | 4 or 12 | 4 or 12 | 12 | ||
Dimensions inches {mm} |
|
|
|
| |
A - Height above mounting plate† | 74 {1880.7} | 74 {1880.7} | 74 {1880.7} | ||
B - Width‡ |
| 56 {1421.4} | 56 {1421.4} | 56 {1421.4} | |
C - Depth‡ |
| 34 {863.6} | 34 {863.6} | 34 {863.6} | |
D - Controller height |
| 11.25 {285.75} | 11.25 {285.75} | 11.25 {285.75} | |
E - Controller width |
| 12.25 {311.15} | 12.25 {311.15} | 12.25 {311.15} | |
F - Controller depth |
| 8.19 {208.03} | 8.19 {208.03} | 8.19 {208.03} | |
Weight lbs {kg} |
|
|
|
| |
Installed |
| 480 {218} | 480 {218} | 480 {218} | |
Shipping |
| 600 {272.2} | 600 {272.2} | 600 {272.2} | |
Voltage Running load amps§ |
|
|
|
| |
120V/1 phase/60 hz (control and mixer) | 8.5 | 8.5 | 8.5 | ||
220V/1 phase/60 hz (control and mixer) | 4.25 | 4.25 | 4.25 | ||
220V/1 phase/50 hz (control) |
| 0.15 | 0.15 | 0.15 | |
220V/3 phase/50 hz (mixer) |
| 2.2 | 2.2 | 2.2 | |
400V/3 phase/50 hz (mixer) |
| 1.1 | 1.1 | 1.1 | |
Compressed air requirements |
|
|
|
| |
Discharge valves |
| 80 psi @ 0.2 ft3/min {5.5 bars @ 0.09 liters/sec}; 1/4 in. NPT fitting | |||
Compressed air feeder |
| 40 psi @ 2.0 ft3/min {2.8 bars @ 0.94 liters/sec}; 1/4 in. NPT fitting | |||
|
|
|
|
|
|
Maximum loader sizes ** |
|
|
|
|
|
Number of 20 inch loaders |
| 2 | 2 | 3 | |
Number of 15 inch loaders |
| 2 | 4 | 6 | |
|
|
|
|
|
|
|
|
|
|
|
|
CONTROL |
MOUNTING INTERFACE
IBO4
SPECIFICATION NOTES:
*Maximum throughput rates are based on 35 lbft3 pelletized material and using all dispense valves. Use of feeders for minor ingredients will reduce this rate. Refer to the selection guide for more specific throughput information.
†The optional flow control valve will add 6.5 in. {165 mm} to the total height. We recommend using the flow control valve when mounting the blender to a stand, surge bin or hopper.
‡Feeders will increase depth dimensions. Please refer to feeder specification.
§Each auger feeder requires an additional 1 amp @ 120V or 0.5 amp @ 240V.
**Maximum loader sizes may be used only when the loader is adjacent to loaders of a smaller diameter.
One Conair Drive ● Pittsburgh, PA 15202 ●
APPENDIX B