Conair GB/ WSB manual Exit

Page 19

To run a LOWER PERCENTAGE then 00.1 percent, read:

PARAMETERS, _XT parameter.

To place UPPER LIMITS on the thumbwheel settings, read: PARAMETERS, _SE Parameter.

To LOCK OUT others from changing settings, read:

KEYPAD, STAR FUNCTIONS, (*78) - Changing the Password.

To blend TWO NATURAL materials instead of Natural and Regrind, read: KEYPAD, STAR FUNCTIONS, (*69) - the TWO NATURALS flag.

To TRACK MATERIAL usage, read:

KEYPAD, VIEW DATA, and PARAMETERS, PRT Parameter.

To VERIFY ACCURACY of the entire system, read:

PRINTER OUTPUT and TROUBLESHOOTING sections.

READ the rest of the manual at your leisure to learn more about how your WEIGH SCALE BLENDER works and what else it can do.

KEYSTROKE SEQUENCE for these or other SPECIAL FEATURES

With STOP END OF CYCLE

switch DOWN,

 

 

 

Turn POWER ON.

Wait 5 seconds, until display says (

x.x)

Press:

*

Display will

say (PASSWORD)

 

Press:

22222

Display will

say (P

x.x)

 

 

 

This is the PROGRAM MODE

 

To alter a PARAMETER;

press: PARA key

 

 

Press repeatedly until the parameter you want is displayed.

 

If you pass it, use the * key to back up.

 

 

With the proper one displayed,

enter the NEW parameter number.

Enter 5 digits; use leading zeros if necessary.

 

For correct entries, follow specific directions given in the

PARAMETER section.

 

 

 

Press:

EXIT

when correct

parameter has been entered.

 

To make a (*XX) entry:

 

 

 

 

Be in the PROGRAM

mode, same as above.

 

 

 

 

Display will

say (P

x.x)

 

Press:

*

Display will

say (INSTR --)

 

Enter the 2 digit

code.

 

 

 

For correct entries, follow specific directions given in the

KEYPAD section, STAR FUNCTIONS.

 

 

Press:

EXIT

when correct

information has been entered.

When finished, press EXIT again to exit the PROGRAM MODE.

Page 20

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Gravimetric Blenders Date Manual Number UGB006/1103 Serial numbers Model numbers Part Operation Part Troubleshooting / SoftwarePart Hardware Maintenance Four Component SoftwareProceed to Safety Hazards Next Assembly InstructionsCheck OUT Procedure Special FeaturesAdditional MIX Blade Hazard Safety Hazards MIX BladesSafety Features Safety Interlock Switch Proceed to Assembly NextDisclaimers On the Next Part AssemblyLoad Cells are Easily Damaged Please Be CarefulPage Proceed to Check OUT Procedure Next Wiring ConsiderationsTouch Weigh BIN Very Lightly Procedure What should Happen Plug in ControllerTurn Power on AT this PointPress NAT KEY Press Alarm KEYPress REG KEY LED #Page Exit PasswordCAL Part Operation Load Cell CalibrationBe Sure CAL OFFCOL Proceed to Normal Operation NextOper Operate GB/WSB 240R Selected Models Special Instructions Micro Pulse GB/WSB MBInstructions for Normal Operation If Problems DevelopPower OFF Power onNormal Operating Sequence Each Cycle Exit Regrind ROM OK Eight Character DisplayLED Lights Right Column AlarmsStrobe Light and Beeper Alarms Alarm SilenceMixer Motor Outlet Mixer Motor ON/OFF/TIMED SwitchMixer Motor Fuse Keypad Internal FusesDate RCP Keypad Automatic Operation ModeRecipe RUNBtch SaveTABLE, FLG Page TAG FastALL Keypad Manual ModeTime ADD TimedPage Keypad Program Mode Star Functions ParaYLD Ctrl Page Page Page Page Page Page Page Page Parameter List Brief Explanations ParametersMIX Time XXX RLO Page CPL Full Explanation of Parameters MPO No ALARM, no RetriesMIX BER KDF / WDFPage ROV Page Example RHL is Set 10 percent Page SET SettingPage Page Page Page Page TCV + TRC XCV + XRCXTP XUL XALLIQ PTDMCT Page MPO RAL NAL CAL AAL MIX JOG Parameter Default Settings Four SoftwareFLG RPO NPO CPO APONTI NPT CPT APT RWTRTI NWTChanging Parameters Total Prnt OFFPrnt REG Natural COLFinal DISP,% What to Check for Page Page Page Calibrate Natural Special TestsTime Time NaturalCycles Last Printed 11/01/90 Material Usage InformationPARAMETER, PRT Date Time Totals Grand PCT CurrentPart IV Troubleshooting What to do Increasing Throughput Typical Problems Page Normal Operating Sequence Material Runs OUT Verifying Load Cell Function CNT OFF Load Cell RAW Signal ReadoutCNT Results to Expect Clear ALL Restart Clear RoutineCore Dump Weigh BIN Dump Valve Soft Close Clean OUT Issues MIX Problems Page Full Recalibration of Load CellsZero WaitWeigh Bins Blender Preventive MaintenanceDispense Gates Load CellsThese Instructions for Totalizers only Totalize Special Totalizer FunctionStop END of Cycle BlenderComputer Outputs Wiring Supplement Call Appendix A-2 Gravimetric Batch Blenders Autoweigh GBM Series Models SpecificationsTOP View Front View Side View Gravimetric Batch Blenders AutoWeigh GB100 Series ModelsGravimetric Batch Blenders GB 220 and 420 Models 120V/1 phase/50-60 Hz 240V/1 phase/50-60 HzTOP View Mounting Interface Gravimetric Batch Blenders AutoWeigh GB240 and GB440 Models2124 Gravimetric Batch Blenders AutoWeigh GB900 Series ModelsGB1840 GB1860 Gravimetric Batch Blenders AutoWeigh GB1840 and 1860 ModelsControl Remote Mounted Models WSBM22 WSBM131 WSBM140 Gravimetric Batch Blenders Wsbm Series modelsSide View Front View Side View, R Model Front View, R Model Gravimetric Batch Blenders WSB 100 and 100R Models24.4 Gravimetric Batch Blenders WSB 220 and 420 ModelsWSB442 Gravimetric Batch Blenders WSB 240/440 and 240/440R ModelsGravimetric Batch Blenders WSB 1840, 1850 and 1860 Models Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C
Top Page Image Contents