Conair GB/ WSB manual Additive, Xxx

Page 44

JOG 03030 Mix blade JOG count and interval

This parameter sets how many jogs will occur and how often.

FCV 00006 TIME the Flow Control valve delays before opening (sec.).

This parameter holds each batch in the mix chamber for a time to assure mixing. This is only for units equipped with the optional flow control valve under the mix chamber.

DTI 00006 Weigh bin dump TIME at end of cycle. (seconds)

This parameter sets the maximum open, or dump time for the weigh bin. No change is required.

KDF 00010 Maximum variation in GRAMS between two consecutive weight

WDF 00010 readings for reading to be accepted. (x or x.x)

KDF controls sensitivity of weight readings during calibration of load cells. No change is required.

WDF controls the sensitivity of weight readings during normal operation. If excessive vibration interferes with weight readings you may have to increase this number.

BER 00200 Excess GRAM weight before dispense is aborted.

This parameter controls sensitivity of the emergency "bailout" routine that prevents overfilling of the weigh bin.

No change is required.

CXT 00000 Move decimal left on color and additive settings. AXT 00000

These parameters allow entry

of less then (00.1) percent for

COLOR or

ADDITIVE.

 

 

 

 

 

When

set

to

"00010" settings

are

read

as

X.XX

percent.

When

set

to

"00100" settings

are

read

as

.XXX

percent.

ROC 00000 These three parameters help control regrind usage. ROV 00000

RHL 00000

ROC indicates the PERCENT of REGRIND that will be treated as natural when COLOR and ADDITIVE dispenses are calculated. This adds some color or additive to your regrind.

ROV is for closed loop fully automatic reprocessing of regrind scrap. This parameter will detect when more regrind is being produced than consumed, and override the current setting to use a higher amount. This helps prevent material backing up in your grinder.

RHL has effect only if level sensors are added to your unit to detect material level in the regrind hopper. These level sensors can alter regrind percent usage.

FUL 20000 Full batch weight, determined by weigh bin size.

MAX 30000 Maximum GRAM weight the software will target.

FUL is the target weight that is blended each cycle. Change only

Page 45

Image 44
Contents Gravimetric Blenders Date Manual Number UGB006/1103 Serial numbers Model numbers Part Troubleshooting / Software Part Hardware MaintenanceFour Component Software Part OperationAssembly Instructions Check OUT ProcedureSpecial Features Proceed to Safety Hazards NextSafety Hazards MIX Blades Safety Features Safety Interlock SwitchProceed to Assembly Next Additional MIX Blade HazardDisclaimers Part Assembly Load Cells are Easily DamagedPlease Be Careful On the NextPage Wiring Considerations Proceed to Check OUT Procedure NextProcedure What should Happen Plug in Controller Turn Power onAT this Point Touch Weigh BIN Very LightlyPress Alarm KEY Press REG KEYLED # Press NAT KEYPage Password ExitPart Operation Load Cell Calibration Be SureCAL OFF CALProceed to Normal Operation Next OperOperate COLSelected Models Special Instructions Micro PulseGB/WSB MB GB/WSB 240RIf Problems Develop Power OFFPower on Instructions for Normal OperationNormal Operating Sequence Each Cycle Exit Regrind Eight Character Display ROM OKRight Column Alarms Strobe Light and Beeper AlarmsAlarm Silence LED LightsMixer Motor Fuse Mixer Motor ON/OFF/TIMED SwitchMixer Motor Outlet Internal Fuses KeypadDate Keypad Automatic Operation Mode RecipeRUN RCPTABLE, FLG SaveBtch Page Fast TAGKeypad Manual Mode ALLTimed Time ADDPage Keypad Program Mode YLD Ctrl ParaStar Functions Page Page Page Page Page Page Page Page MIX Time ParametersParameter List Brief Explanations XXX RLO Page CPL Full Explanation of Parameters No ALARM, no Retries MPOMIX KDF / WDF BERPage ROV Page Example RHL is Set 10 percent Page Setting SETPage Page Page Page Page XTP XCV + XRCTCV + TRC XAL XULMCT PTDLIQ Page Parameter Default Settings Four Software FLG RPO NPO CPOAPO MPO RAL NAL CAL AAL MIX JOGNPT CPT APT RWT RTINWT NTIChanging Parameters Prnt OFF PrntREG Natural COL TotalFinal DISP,% What to Check for Page Page Page Special Tests TimeTime Natural Calibrate NaturalMaterial Usage Information PARAMETER, PRTDate Time Totals Grand PCT Current Cycles Last Printed 11/01/90Part IV Troubleshooting What to do Increasing Throughput Typical Problems Page Normal Operating Sequence Material Runs OUT Verifying Load Cell Function CNT Load Cell RAW Signal ReadoutCNT OFF Results to Expect Core Dump Clear RoutineClear ALL Restart Weigh BIN Dump Valve Soft Close Clean OUT Issues MIX Problems Page Recalibration of Load Cells ZeroWait FullBlender Preventive Maintenance Dispense GatesLoad Cells Weigh BinsThese Instructions for Totalizers only Special Totalizer Function Stop END of CycleBlender TotalizeComputer Outputs Wiring Supplement Call Appendix A-2 Specifications Gravimetric Batch Blenders Autoweigh GBM Series ModelsGravimetric Batch Blenders AutoWeigh GB100 Series Models TOP View Front View Side View120V/1 phase/50-60 Hz 240V/1 phase/50-60 Hz Gravimetric Batch Blenders GB 220 and 420 ModelsGravimetric Batch Blenders AutoWeigh GB240 and GB440 Models TOP View Mounting InterfaceGravimetric Batch Blenders AutoWeigh GB900 Series Models 2124Gravimetric Batch Blenders AutoWeigh GB1840 and 1860 Models GB1840 GB1860Gravimetric Batch Blenders Wsbm Series models Control Remote Mounted Models WSBM22 WSBM131 WSBM140Gravimetric Batch Blenders WSB 100 and 100R Models Side View Front View Side View, R Model Front View, R ModelGravimetric Batch Blenders WSB 220 and 420 Models 24.4Gravimetric Batch Blenders WSB 240/440 and 240/440R Models WSB442Gravimetric Batch Blenders WSB 1840, 1850 and 1860 Models Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C