Conair GB/ WSB manual Gravimetric Batch Blenders

Page 109

SPECIFICATIONS

TPBS004/1199

GRAVIMETRIC BATCH BLENDERS

WSB 920, 940, 950 and 960 Models

NOTE: Loader configuration is the same for all models.

CONTROL

MODELS

 

WSB920

WSB940

WSB950

WSB960

Performance characteristics

 

 

 

 

 

Batch size lbs {g}

 

19.8 {9000}

19.8 {9000}

19.8 {9000}

19.8 {9000}

Maximum throughput lbs/hr {kg/hr}*

5200 {2359}

3300 {1487}

2492 {1132}

2124 {965}

Bin capacity - main ingredient

ft3 {liter}

6.7 {189.7}

6.7 {189.7}

6.7 {189.7}

NA

Bin capacity - minor ingredient

ft3 {liter}

NA

3.8 {107.6}

3.8 {107.6}

3.8 {107.6}

Maximum number of materials

 

6

8

9

10

Number of discharge valves

 

2

4

5

6

Number of additive feeders

 

up to 4

up to 4

up to 4

up to 4

Control software (# of components)

4 or 12

4 or 12

12

12

Dimensions inches {mm}

 

 

 

 

 

A - Height above mounting plate

74 {1880.7}

74 {1880.7}

74 {1880.7}

74 {1880.7}

B - Width

 

56 {1421.4}

56 {1421.4}

56 {1421.4}

56 {1421.4}

C - Depth

 

34.4 {875.3}

34.4 {875.3}

34.4 {875.3}

34.4 {875.3}

D - Controller height

 

11.25 {285.75}

11.25 {285.75}

11.25 {285.75}

11.25 {285.75}

E - Controller width

 

12.25 {311.15}

12.25 {311.15}

12.25 {311.15}

12.25 {311.15}

F - Controller depth

 

8.19 {208.03}

8.19 {208.03}

8.19 {208.03}

8.19 {208.03}

Weight lbs {kg}

 

 

 

 

 

Installed

 

480 {218}

480 {218}

480 {218}

480 {218}

Shipping

 

600 {272.2}

600 {272.2}

600 {272.2}

600 {272.2}

Voltage Running load amps

 

 

 

 

 

120V/1 phase/60 hz (control and mixer)

8.5

8.5

8.5

8.5

220V/1 phase/60 hz (control and mixer)

4.3

4.3

4.3

4.3

220V/1 phase/50 hz (control)

 

0.15

0.15

0.15

0.15

220V/3 phase/50 hz (mixer)

 

2.2

2.2

2.2

2.2

400V/3 phase/50 hz (mixer)

 

1.1

1.1

1.1

1.1

Compressed air requirements

 

 

 

 

 

Discharge valves

 

80 psi @ 0.2 ft3/min {5.5 bars @ 0.09 liters/sec}; 1/4 in. NPT fitting

Compressed air feeder

 

40 psi @ 2.0 ft3/min {2.8 bars @ 0.94 liters/sec}; 1/4 in. NPT fitting

Maximum loader sizes§

 

 

 

 

 

Number of 20 inch loaders

 

2

2

2

3

Number of 15 inch loaders

 

2

4

5

6

 

 

 

 

 

 

MOUNTING INTERFACE

IB04

SPECIFICATION NOTES:

*Maximum throughput rates are based on using all dispense valves. Use of feeders for minor ingredients will reduce this rate.

Feeders will increase width and depth dimensions. Please refer to feeder specification.

Each auger feeder requires an additional 1 amp @ 120V or 0.5 amp @ 240V.

§Maximum loader sizes may be used only when the loader is adjacent to loaders of a smaller size.

APPLICATION NOTE:

We recommend using a flow con- trol valve when mounting the blender to a stand, surge bin or hopper.

One Conair Drive Pittsburgh, PA 15202 412-312-6000 FAX 412-312-6227 www.conairnet.com

APPENDIX B

Image 109
Contents Gravimetric Blenders Date Manual Number UGB006/1103 Serial numbers Model numbers Part Hardware Maintenance Part Troubleshooting / SoftwareFour Component Software Part OperationCheck OUT Procedure Assembly InstructionsSpecial Features Proceed to Safety Hazards NextSafety Features Safety Interlock Switch Safety Hazards MIX BladesProceed to Assembly Next Additional MIX Blade HazardDisclaimers Load Cells are Easily Damaged Part AssemblyPlease Be Careful On the NextPage Proceed to Check OUT Procedure Next Wiring ConsiderationsTurn Power on Procedure What should Happen Plug in ControllerAT this Point Touch Weigh BIN Very LightlyPress REG KEY Press Alarm KEYLED # Press NAT KEYPage Exit PasswordBe Sure Part Operation Load Cell CalibrationCAL OFF CALOper Proceed to Normal Operation NextOperate COLMicro Pulse Selected Models Special InstructionsGB/WSB MB GB/WSB 240RPower OFF If Problems DevelopPower on Instructions for Normal OperationNormal Operating Sequence Each Cycle Exit Regrind ROM OK Eight Character DisplayStrobe Light and Beeper Alarms Right Column AlarmsAlarm Silence LED LightsMixer Motor Outlet Mixer Motor ON/OFF/TIMED SwitchMixer Motor Fuse Keypad Internal FusesDate Recipe Keypad Automatic Operation ModeRUN RCPBtch SaveTABLE, FLG Page TAG FastALL Keypad Manual ModeTime ADD TimedPage Keypad Program Mode Star Functions ParaYLD Ctrl Page Page Page Page Page Page Page Page Parameter List Brief Explanations ParametersMIX Time XXX RLO Page CPL Full Explanation of Parameters MPO No ALARM, no RetriesMIX BER KDF / WDFPage ROV Page Example RHL is Set 10 percent Page SET SettingPage Page Page Page Page TCV + TRC XCV + XRCXTP XUL XALLIQ PTDMCT Page FLG RPO NPO CPO Parameter Default Settings Four SoftwareAPO MPO RAL NAL CAL AAL MIX JOGRTI NPT CPT APT RWTNWT NTIChanging Parameters Prnt Prnt OFFREG Natural COL TotalFinal DISP,% What to Check for Page Page Page Time Special TestsTime Natural Calibrate NaturalPARAMETER, PRT Material Usage InformationDate Time Totals Grand PCT Current Cycles Last Printed 11/01/90Part IV Troubleshooting What to do Increasing Throughput Typical Problems Page Normal Operating Sequence Material Runs OUT Verifying Load Cell Function CNT OFF Load Cell RAW Signal ReadoutCNT Results to Expect Clear ALL Restart Clear RoutineCore Dump Weigh BIN Dump Valve Soft Close Clean OUT Issues MIX Problems Page Zero Recalibration of Load CellsWait FullDispense Gates Blender Preventive MaintenanceLoad Cells Weigh BinsThese Instructions for Totalizers only Stop END of Cycle Special Totalizer FunctionBlender TotalizeComputer Outputs Wiring Supplement Call Appendix A-2 Gravimetric Batch Blenders Autoweigh GBM Series Models SpecificationsTOP View Front View Side View Gravimetric Batch Blenders AutoWeigh GB100 Series ModelsGravimetric Batch Blenders GB 220 and 420 Models 120V/1 phase/50-60 Hz 240V/1 phase/50-60 HzTOP View Mounting Interface Gravimetric Batch Blenders AutoWeigh GB240 and GB440 Models2124 Gravimetric Batch Blenders AutoWeigh GB900 Series ModelsGB1840 GB1860 Gravimetric Batch Blenders AutoWeigh GB1840 and 1860 ModelsControl Remote Mounted Models WSBM22 WSBM131 WSBM140 Gravimetric Batch Blenders Wsbm Series modelsSide View Front View Side View, R Model Front View, R Model Gravimetric Batch Blenders WSB 100 and 100R Models24.4 Gravimetric Batch Blenders WSB 220 and 420 ModelsWSB442 Gravimetric Batch Blenders WSB 240/440 and 240/440R ModelsGravimetric Batch Blenders WSB 1840, 1850 and 1860 Models Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C