Conair GB/ WSB Instructions for Normal Operation, Color, Natural, Additive, Saving, Power OFF

Page 17

INSTRUCTIONS FOR NORMAL OPERATION

OPERATION: ....very simple.

1.Fill HOPPERS: REGRIND, NATURAL, COLOR, ADDITIVE: in hoppers as labeled.

If auger feeders are used:

COLOR in RIGHT side feeder,

ADDITIVE in LEFT side feeder.

2. Set THUMBWHEEL switches for percentages desired.

REGRIND, enter as a percent of the entire mix. (xx percent)

COLOR,

as

a

percent

of

the

NATURAL.

(xx.x

percent)

ADDITIVE,

as

a

percent

of

the

NATURAL.

(xx.x

percent)

3.On Controller, turn POWER ON, set STOP, and PAUSE switches UP. Switch MIXER motor DOWN to run for a timed period each cycle.

Unit will now operate automatically to maintain a level of material high enough to cover the sensor.

Use the STOP or PAUSE switches to stop the dispensing of material. Turn POWER off only on final shutdown. Battery-backed RAM ensures all information is retained even with power turned off.

The KEYPAD is only for: 1. MANUAL TESTING.

2.ALTERATION of INTERNAL PARAMETERS

----------------------------------------------------------------------

AFTER SEVERAL DAYS OF PROPER OPERATION:

Save all parameter information to the EEPROM for future retrieval should software problems develop later.

To SAVE all parameter information to the EEPROM:

+---------------------------------------------------

 

 

+

¦ Press:

*

Display will say:

(PASSWORD) ¦

¦ Press:

22222

Display will say:

(P

x.x) ¦

¦ Press:

*

Display will say:

(INSTR --) ¦

¦ Press:

23

Display will say:

(SAVING ) ¦

¦ Wait:

when done,

Display will say:

(P

x.x) ¦

¦ Press: EXIT

Display will say:

(

x.x) ¦

+---------------------------------------------------

 

 

+

IF PROBLEMS DEVELOP:

RETRIEVE this correct copy of the parameters from the EEPROM. This

clears corrupted

data from RAM and corrects most software problems.

+

----------------------------------------

+

¦

Switch:

POWER OFF.

¦

¦

Hold:

the "CE" key down.

¦

¦

Switch:

POWER ON.

¦

¦

Release:

the "CE" key.

¦

¦

 

Display will say ( CLEAR

) ¦

¦

If you do not see ( CLEAR )

¦

¦

on the display, do it again.

¦

+

----------------------------------------

+

Page 18

Image 17
Contents Gravimetric Blenders Date Manual Number UGB006/1103 Serial numbers Model numbers Part Hardware Maintenance Part Troubleshooting / SoftwareFour Component Software Part OperationCheck OUT Procedure Assembly InstructionsSpecial Features Proceed to Safety Hazards NextSafety Features Safety Interlock Switch Safety Hazards MIX BladesProceed to Assembly Next Additional MIX Blade HazardDisclaimers Load Cells are Easily Damaged Part AssemblyPlease Be Careful On the NextPage Proceed to Check OUT Procedure Next Wiring ConsiderationsTurn Power on Procedure What should Happen Plug in ControllerAT this Point Touch Weigh BIN Very LightlyPress REG KEY Press Alarm KEYLED # Press NAT KEYPage Exit PasswordBe Sure Part Operation Load Cell CalibrationCAL OFF CALOper Proceed to Normal Operation NextOperate COLMicro Pulse Selected Models Special InstructionsGB/WSB MB GB/WSB 240RPower OFF If Problems DevelopPower on Instructions for Normal OperationNormal Operating Sequence Each Cycle Exit Regrind ROM OK Eight Character DisplayStrobe Light and Beeper Alarms Right Column AlarmsAlarm Silence LED LightsMixer Motor Fuse Mixer Motor ON/OFF/TIMED SwitchMixer Motor Outlet Keypad Internal FusesDate Recipe Keypad Automatic Operation ModeRUN RCPTABLE, FLG SaveBtch Page TAG FastALL Keypad Manual ModeTime ADD TimedPage Keypad Program Mode YLD Ctrl ParaStar Functions Page Page Page Page Page Page Page Page MIX Time ParametersParameter List Brief Explanations XXX RLO Page CPL Full Explanation of Parameters MPO No ALARM, no RetriesMIX BER KDF / WDFPage ROV Page Example RHL is Set 10 percent Page SET SettingPage Page Page Page Page XTP XCV + XRCTCV + TRC XUL XALMCT PTDLIQ Page FLG RPO NPO CPO Parameter Default Settings Four SoftwareAPO MPO RAL NAL CAL AAL MIX JOGRTI NPT CPT APT RWTNWT NTIChanging Parameters Prnt Prnt OFFREG Natural COL TotalFinal DISP,% What to Check for Page Page Page Time Special TestsTime Natural Calibrate NaturalPARAMETER, PRT Material Usage InformationDate Time Totals Grand PCT Current Cycles Last Printed 11/01/90Part IV Troubleshooting What to do Increasing Throughput Typical Problems Page Normal Operating Sequence Material Runs OUT Verifying Load Cell Function CNT Load Cell RAW Signal ReadoutCNT OFF Results to Expect Core Dump Clear RoutineClear ALL Restart Weigh BIN Dump Valve Soft Close Clean OUT Issues MIX Problems Page Zero Recalibration of Load CellsWait FullDispense Gates Blender Preventive MaintenanceLoad Cells Weigh BinsThese Instructions for Totalizers only Stop END of Cycle Special Totalizer FunctionBlender TotalizeComputer Outputs Wiring Supplement Call Appendix A-2 Gravimetric Batch Blenders Autoweigh GBM Series Models SpecificationsTOP View Front View Side View Gravimetric Batch Blenders AutoWeigh GB100 Series ModelsGravimetric Batch Blenders GB 220 and 420 Models 120V/1 phase/50-60 Hz 240V/1 phase/50-60 HzTOP View Mounting Interface Gravimetric Batch Blenders AutoWeigh GB240 and GB440 Models2124 Gravimetric Batch Blenders AutoWeigh GB900 Series ModelsGB1840 GB1860 Gravimetric Batch Blenders AutoWeigh GB1840 and 1860 ModelsControl Remote Mounted Models WSBM22 WSBM131 WSBM140 Gravimetric Batch Blenders Wsbm Series modelsSide View Front View Side View, R Model Front View, R Model Gravimetric Batch Blenders WSB 100 and 100R Models24.4 Gravimetric Batch Blenders WSB 220 and 420 ModelsWSB442 Gravimetric Batch Blenders WSB 240/440 and 240/440R ModelsGravimetric Batch Blenders WSB 1840, 1850 and 1860 Models Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C