Conair GB/ WSB manual Timed, Time ADD

Page 31

The following manual functions are available in the MANUAL mode.

SETTING: Press once followed by one of 3 keys: REG, COL, or ADD. The

(SET) current thumbwheel setting is displayed. If, while in the program mode, the keypad was used to enter this setting then it will not match the thumbwheel setting.

EXIT will exit the sequence.

OPERATE:

Press once

followed by one of 8

keys: REG, NAT, COL, ADD,

(OPER)

DUP, ALM, MIX, or HOLD. The selected output operates until

 

the key is

pressed again or another output is selected.

 

Only 1 output will be active at

a time.

 

EXIT will exit the sequence and

close all outputs.

TIMED:

Press

once

followed by one of 4

keys: REG, NAT, COL, or

(TIME)

ADD.

A time in interrupts is requested; (TIME ---). Three

 

digits must be entered specifying a dispense time up to 999

 

interrupts

(about 4 seconds max.). CE will cancel entry

 

before last digit is entered. Following a full 3 digit time

 

entry, the

specified output is activated for the time

 

requested. After the dispense is weighed, the dump valve

 

automatically operates to empty

the weigh bin. If a printer

 

is on line

and the Print flag is ON, then output information

will be printed. EXIT will exit the sequence.

CALIBRATE: (RATE) Press once and then press one of 4 keys: REG, NAT,

(CAL) COL, or ADD. A dispense will occur for 2 seconds. If the amount dispensed is less then 50 grams, a second dispense will occur for 20 seconds. Using the resulting weight and time, the processor calculates a proper beginning point dump rate for the start of production blending. After each dispense is weighed, the weigh bin dump valve automatically operates to empty the weigh bin. If a printer is on line and the Print flag is ON (see KEYPAD *54), then output information will be printed. EXIT will exit the sequence.

If the display says (DO AGAIN), press any key to cause the process to repeat itself. If the display then says

( NO GOOD), the weight dispensed was below 5 grams, not enough for a valid calibration.

During initial operation, after each power up, the blender calibrates itself completely automatically, regardless of how far off the initial flow rate may be. This may take several cycles. During normal operation, calibration correction occurs continuously.

Since this unit adjusts flow rates automatically, manual Rate Calibration is not necessary for proper operation.

ZERO WT:

THIS HAS BEEN

DONE AT THE FACTORY. IT SHOULD NOT BE

(ZERO)

NECESSARY

FOR

YOU TO DO

THIS AGAIN.

 

 

Press the

ZERO key once

to set the displayed gram

weight of

 

the empty

bin

to zero. BE SURE the load cells are

plugged

 

into the controller. Be sure the bin is properly

in place

 

and EMPTY

when this key

is pressed.

 

Page 32

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Gravimetric Blenders Date Manual Number UGB006/1103 Serial numbers Model numbers Part Operation Part Troubleshooting / SoftwarePart Hardware Maintenance Four Component SoftwareProceed to Safety Hazards Next Assembly InstructionsCheck OUT Procedure Special FeaturesAdditional MIX Blade Hazard Safety Hazards MIX BladesSafety Features Safety Interlock Switch Proceed to Assembly NextDisclaimers On the Next Part AssemblyLoad Cells are Easily Damaged Please Be CarefulPage Proceed to Check OUT Procedure Next Wiring ConsiderationsTouch Weigh BIN Very Lightly Procedure What should Happen Plug in ControllerTurn Power on AT this PointPress NAT KEY Press Alarm KEYPress REG KEY LED #Page Exit PasswordCAL Part Operation Load Cell CalibrationBe Sure CAL OFFCOL Proceed to Normal Operation NextOper OperateGB/WSB 240R Selected Models Special InstructionsMicro Pulse GB/WSB MBInstructions for Normal Operation If Problems DevelopPower OFF Power onNormal Operating Sequence Each Cycle Exit Regrind ROM OK Eight Character DisplayLED Lights Right Column AlarmsStrobe Light and Beeper Alarms Alarm SilenceMixer Motor Outlet Mixer Motor ON/OFF/TIMED SwitchMixer Motor Fuse Keypad Internal FusesDate RCP Keypad Automatic Operation ModeRecipe RUNBtch SaveTABLE, FLG Page TAG FastALL Keypad Manual ModeTime ADD TimedPage Keypad Program Mode Star Functions ParaYLD Ctrl Page Page Page Page Page Page Page Page Parameter List Brief Explanations ParametersMIX Time XXX RLO Page CPL Full Explanation of Parameters MPO No ALARM, no RetriesMIX BER KDF / WDFPage ROV Page Example RHL is Set 10 percent Page SET SettingPage Page Page Page Page TCV + TRC XCV + XRCXTP XUL XALLIQ PTDMCT Page MPO RAL NAL CAL AAL MIX JOG Parameter Default Settings Four SoftwareFLG RPO NPO CPO APONTI NPT CPT APT RWTRTI NWTChanging Parameters Total Prnt OFFPrnt REG Natural COLFinal DISP,% What to Check for Page Page Page Calibrate Natural Special TestsTime Time NaturalCycles Last Printed 11/01/90 Material Usage InformationPARAMETER, PRT Date Time Totals Grand PCT CurrentPart IV Troubleshooting What to do Increasing Throughput Typical Problems Page Normal Operating Sequence Material Runs OUT Verifying Load Cell Function CNT OFF Load Cell RAW Signal ReadoutCNT Results to Expect Clear ALL Restart Clear RoutineCore Dump Weigh BIN Dump Valve Soft Close Clean OUT Issues MIX Problems Page Full Recalibration of Load CellsZero WaitWeigh Bins Blender Preventive MaintenanceDispense Gates Load CellsThese Instructions for Totalizers only Totalize Special Totalizer FunctionStop END of Cycle BlenderComputer Outputs Wiring Supplement Call Appendix A-2 Gravimetric Batch Blenders Autoweigh GBM Series Models SpecificationsTOP View Front View Side View Gravimetric Batch Blenders AutoWeigh GB100 Series ModelsGravimetric Batch Blenders GB 220 and 420 Models 120V/1 phase/50-60 Hz 240V/1 phase/50-60 HzTOP View Mounting Interface Gravimetric Batch Blenders AutoWeigh GB240 and GB440 Models2124 Gravimetric Batch Blenders AutoWeigh GB900 Series ModelsGB1840 GB1860 Gravimetric Batch Blenders AutoWeigh GB1840 and 1860 ModelsControl Remote Mounted Models WSBM22 WSBM131 WSBM140 Gravimetric Batch Blenders Wsbm Series modelsSide View Front View Side View, R Model Front View, R Model Gravimetric Batch Blenders WSB 100 and 100R Models24.4 Gravimetric Batch Blenders WSB 220 and 420 ModelsWSB442 Gravimetric Batch Blenders WSB 240/440 and 240/440R ModelsGravimetric Batch Blenders WSB 1840, 1850 and 1860 Models Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C
Top Page Image Contents