Conair GB/ WSB manual

Page 56

over 3000 grams probably would exceed the volume capacity of the bin and, therefore, not be accurate. We have set the full batch weight to 2000 grams which we considered a conservative full batch weight. Higher batch weights will increase maximum throughput rates.

If your Regrind is very fluffy and you use a lot of it, you may find 2000 grams to be too much volume for the bin. Select a lower total batch weight such as 1500 to ensure that the bin never overflows of fills completely to the dump valve.

======================================================================

MAX (set automatically if FUL parameter is changed)

MAX is the maximum gram weight which the software will allow as a target for dispensing. The initial Full weight target is set by the FUL parameter. As dispenses progress, an over dispense of one component may cause a new target to be calculated for future dispenses in order to maintain proper requested ratios. A recalculated target is not allowed to exceed the value held in the MAX parameter.

If you change the FUL parameter, the MAX parameter will automatically be set to a value 50 percent higher then the FUL setting.

======================================================================

TH and TL

TH and TL are acceptable error limits for TARE WEIGHT.

Before a dispense cycle begins, the software checks to see that the weigh bin is in place and not already full of material. To do this it looks at the starting TARE weight.

If Tare weight is below the value of TL, (50 grams), the software assumes the bin is either missing or hung up on something. In this case the ALARM sounds.

If Tare weight is above the value of TH (100 grams), the software assumes material is in the bin. In this case the ALARM sounds and the weight bin dump flap operates in an attempt to empty the weigh bin.

If you are processing a material that has a tendency to hang up in the corners of the bin, you may wish to widen the range of acceptable starting tare weight. Since tare weight is always subtracted from dispense weights, these errors do not effect accuracy.

======================================================================

PRT (change to get AUTOMATIC printing of material totals)

PRT, when set to any number other then zero, will cause the processor to output all current material usage totals, at regular time intervals, to the printer port. The number you enter will dictate the time interval in minutes. All timing starts from MIDNIGHT. for example, an entry of 00120 will cause totals to print at 2 AM, 4 AM, 6 AM, etc. Printing always waits until a cycle has just ended. A setting of 10000 is a special case. This will cause a printout after every cycle. A printer must be connected. If one is not, the routine will abort and blending will continue.

======================================================================

Page 57

Image 56
Contents Gravimetric Blenders Date Manual Number UGB006/1103 Serial numbers Model numbers Part Troubleshooting / Software Part Hardware MaintenanceFour Component Software Part OperationAssembly Instructions Check OUT ProcedureSpecial Features Proceed to Safety Hazards NextSafety Hazards MIX Blades Safety Features Safety Interlock SwitchProceed to Assembly Next Additional MIX Blade HazardDisclaimers Part Assembly Load Cells are Easily DamagedPlease Be Careful On the NextPage Wiring Considerations Proceed to Check OUT Procedure NextProcedure What should Happen Plug in Controller Turn Power onAT this Point Touch Weigh BIN Very LightlyPress Alarm KEY Press REG KEYLED # Press NAT KEYPage Password ExitPart Operation Load Cell Calibration Be SureCAL OFF CALProceed to Normal Operation Next OperOperate COLSelected Models Special Instructions Micro PulseGB/WSB MB GB/WSB 240RIf Problems Develop Power OFFPower on Instructions for Normal OperationNormal Operating Sequence Each Cycle Exit Regrind Eight Character Display ROM OKRight Column Alarms Strobe Light and Beeper AlarmsAlarm Silence LED LightsMixer Motor Fuse Mixer Motor ON/OFF/TIMED SwitchMixer Motor Outlet Internal Fuses KeypadDate Keypad Automatic Operation Mode RecipeRUN RCPTABLE, FLG SaveBtch Page Fast TAGKeypad Manual Mode ALLTimed Time ADDPage Keypad Program Mode YLD Ctrl ParaStar Functions Page Page Page Page Page Page Page Page MIX Time ParametersParameter List Brief Explanations XXX RLO Page CPL Full Explanation of Parameters No ALARM, no Retries MPOMIX KDF / WDF BERPage ROV Page Example RHL is Set 10 percent Page Setting SETPage Page Page Page Page XTP XCV + XRCTCV + TRC XAL XULMCT PTDLIQ Page Parameter Default Settings Four Software FLG RPO NPO CPOAPO MPO RAL NAL CAL AAL MIX JOGNPT CPT APT RWT RTINWT NTIChanging Parameters Prnt OFF PrntREG Natural COL TotalFinal DISP,% What to Check for Page Page Page Special Tests TimeTime Natural Calibrate NaturalMaterial Usage Information PARAMETER, PRTDate Time Totals Grand PCT Current Cycles Last Printed 11/01/90Part IV Troubleshooting What to do Increasing Throughput Typical Problems Page Normal Operating Sequence Material Runs OUT Verifying Load Cell Function CNT Load Cell RAW Signal ReadoutCNT OFF Results to Expect Core Dump Clear RoutineClear ALL Restart Weigh BIN Dump Valve Soft Close Clean OUT Issues MIX Problems Page Recalibration of Load Cells ZeroWait FullBlender Preventive Maintenance Dispense GatesLoad Cells Weigh BinsThese Instructions for Totalizers only Special Totalizer Function Stop END of CycleBlender TotalizeComputer Outputs Wiring Supplement Call Appendix A-2 Specifications Gravimetric Batch Blenders Autoweigh GBM Series ModelsGravimetric Batch Blenders AutoWeigh GB100 Series Models TOP View Front View Side View120V/1 phase/50-60 Hz 240V/1 phase/50-60 Hz Gravimetric Batch Blenders GB 220 and 420 ModelsGravimetric Batch Blenders AutoWeigh GB240 and GB440 Models TOP View Mounting InterfaceGravimetric Batch Blenders AutoWeigh GB900 Series Models 2124Gravimetric Batch Blenders AutoWeigh GB1840 and 1860 Models GB1840 GB1860Gravimetric Batch Blenders Wsbm Series models Control Remote Mounted Models WSBM22 WSBM131 WSBM140Gravimetric Batch Blenders WSB 100 and 100R Models Side View Front View Side View, R Model Front View, R ModelGravimetric Batch Blenders WSB 220 and 420 Models 24.4Gravimetric Batch Blenders WSB 240/440 and 240/440R Models WSB442Gravimetric Batch Blenders WSB 1840, 1850 and 1860 Models Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C