Conair GB/ WSB manual Fast, Tag

Page 29

NOTE: Fractional cycles are not blended. Total weight may be in over the target by as much as one cycle weight.

The EXIT key will exit the BTCH sequence at any point but will NOT cause the system to start a new batch.

If an additional 120 volt output is desired for an alarm, substitute a 4 or 7 for the 00001. 4 turns on the Additive outlet, 7 turns on component 7 output.

If you have a printer connected, totals will print automatically. (see VIEW, * for details).

FAST:

This key

will

allow

you

to exceed the

normal blending rate

 

of your unit.

Once

your system has learned proper flow

 

rates of

each

material,

the timing of

each component

 

dispense

is very consistent cycle to cycle. The FAST key

 

allows one or

more

FAST

REPEAT cycles

to follow a normal

 

calibrated cycle.

In a

FAST REPEAT cycle all components are

 

dispensed simultaneously, without any

weights being taken.

 

Errors in dispense amounts will not be detected. These are,

 

in fact,

volumetric

dispenses, not gravimetric. These

 

dispenses take much

less time. Throughput may be doubled in

 

this manner.

 

 

 

 

 

This key is NOT FUNCTIONAL unless the 4th digit of the "FLG" parameter is set to 1 (xxx1x). To do this, see the SOFTWARE MAINTENANCE section, PARAMETER TABLE, "FLG".

The shorter mixing time may be a problem. So the number of FAST REPEAT cycles is kept as low as possible. Up to 4 repeats may occur.

After pressing the FAST key, use the * key to toggle the FAST flag ON of OFF. When set to (FAST OFF) FAST mode will not operate. When set (FAST ON) every normal calibrated dispense will be followed by up to 4 FAST repeat dispenses.

Press * to toggle between (FAST ON) and (FAST OFF).

Press EXIT, to exit.

When the FAST mode is in operation, the display ( FAST) will flash intermittently.

TAG:

This key (third row,

third key)

allows three pieces of

 

information to be "tagged" onto

all data that is

either

 

printed or retrieved

through the computer port.

The items

 

are WORK ORDER, OPERATOR, and RECIPE number.

 

This key is NOT FUNCTIONAL unless the 2nd digit of the "FLG" parameter is set to 1 (x1xxx). To do this, see the SOFTWARE MAINTENANCE section, PARAMETER TABLE, "FLG".

Press once to display the current Work Order number (WO-----). Press again to display the current Operator

number (OPRTR---). Press again for the Recipe (RECP ---). You may enter or change the Work Order or Operator number when each is displayed. Recipe number can not be altered.

Page 30

Image 29
Contents Gravimetric Blenders Date Manual Number UGB006/1103 Serial numbers Model numbers Part Hardware Maintenance Part Troubleshooting / SoftwareFour Component Software Part OperationCheck OUT Procedure Assembly InstructionsSpecial Features Proceed to Safety Hazards NextSafety Features Safety Interlock Switch Safety Hazards MIX BladesProceed to Assembly Next Additional MIX Blade HazardDisclaimers Load Cells are Easily Damaged Part AssemblyPlease Be Careful On the NextPage Proceed to Check OUT Procedure Next Wiring ConsiderationsTurn Power on Procedure What should Happen Plug in ControllerAT this Point Touch Weigh BIN Very LightlyPress REG KEY Press Alarm KEYLED # Press NAT KEYPage Exit PasswordBe Sure Part Operation Load Cell CalibrationCAL OFF CALOper Proceed to Normal Operation NextOperate COLMicro Pulse Selected Models Special InstructionsGB/WSB MB GB/WSB 240RPower OFF If Problems DevelopPower on Instructions for Normal OperationNormal Operating Sequence Each Cycle Exit Regrind ROM OK Eight Character DisplayStrobe Light and Beeper Alarms Right Column AlarmsAlarm Silence LED LightsMixer Motor Fuse Mixer Motor ON/OFF/TIMED SwitchMixer Motor Outlet Keypad Internal FusesDate Recipe Keypad Automatic Operation ModeRUN RCPTABLE, FLG SaveBtch Page TAG FastALL Keypad Manual ModeTime ADD TimedPage Keypad Program Mode YLD Ctrl ParaStar Functions Page Page Page Page Page Page Page Page MIX Time ParametersParameter List Brief Explanations XXX RLO Page CPL Full Explanation of Parameters MPO No ALARM, no RetriesMIX BER KDF / WDFPage ROV Page Example RHL is Set 10 percent Page SET SettingPage Page Page Page Page XTP XCV + XRCTCV + TRC XUL XALMCT PTDLIQ Page FLG RPO NPO CPO Parameter Default Settings Four SoftwareAPO MPO RAL NAL CAL AAL MIX JOGRTI NPT CPT APT RWTNWT NTIChanging Parameters Prnt Prnt OFFREG Natural COL TotalFinal DISP,% What to Check for Page Page Page Time Special TestsTime Natural Calibrate NaturalPARAMETER, PRT Material Usage InformationDate Time Totals Grand PCT Current Cycles Last Printed 11/01/90Part IV Troubleshooting What to do Increasing Throughput Typical Problems Page Normal Operating Sequence Material Runs OUT Verifying Load Cell Function CNT Load Cell RAW Signal ReadoutCNT OFF Results to Expect Core Dump Clear RoutineClear ALL Restart Weigh BIN Dump Valve Soft Close Clean OUT Issues MIX Problems Page Zero Recalibration of Load CellsWait FullDispense Gates Blender Preventive MaintenanceLoad Cells Weigh BinsThese Instructions for Totalizers only Stop END of Cycle Special Totalizer FunctionBlender TotalizeComputer Outputs Wiring Supplement Call Appendix A-2 Gravimetric Batch Blenders Autoweigh GBM Series Models SpecificationsTOP View Front View Side View Gravimetric Batch Blenders AutoWeigh GB100 Series ModelsGravimetric Batch Blenders GB 220 and 420 Models 120V/1 phase/50-60 Hz 240V/1 phase/50-60 HzTOP View Mounting Interface Gravimetric Batch Blenders AutoWeigh GB240 and GB440 Models2124 Gravimetric Batch Blenders AutoWeigh GB900 Series ModelsGB1840 GB1860 Gravimetric Batch Blenders AutoWeigh GB1840 and 1860 ModelsControl Remote Mounted Models WSBM22 WSBM131 WSBM140 Gravimetric Batch Blenders Wsbm Series modelsSide View Front View Side View, R Model Front View, R Model Gravimetric Batch Blenders WSB 100 and 100R Models24.4 Gravimetric Batch Blenders WSB 220 and 420 ModelsWSB442 Gravimetric Batch Blenders WSB 240/440 and 240/440R ModelsGravimetric Batch Blenders WSB 1840, 1850 and 1860 Models Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C