Conair GB/ WSB Proceed to Normal Operation Next, Operate, Col, Add, Dump, Calibrate, REG Regrind

Page 15

RATE CALIBRATION

RATE CALIBRATION is probably not necessary. The software initially expects STANDARD hardware. However, if you are using an auger feeder on a model with four dispense valves, or a 1/2 inch auger instead of a 1" auger, the software will take 10 or 20 cycles to adjust to correct operation. This slows down the process for a short time, but does not effect accuracy.

If your hardware is STANDARD, or

 

you prefer letting the system SELF ADJUST,

 

you may:

 

 

+---------------------------------------------------

+

¦

 

¦

¦ PROCEED TO:

NORMAL OPERATION

NEXT PAGE ¦

¦

 

¦

+---------------------------------------------------

+

To perform a RATE CALIBRATION:

Have all HOPPERS LOADED with enough material to run for several cycles without running out.

Have the "OFF AT END OF CYCLE" and "PAUSE" switches DOWN.

Press:

*

Display

will

say:

(PASSWORD)

Press:

22222

Display

will

say:

(P

x)

If your system has auger feeders, operate them briefly to ensure they are fully primed. To do so:

Press:

OPER

Display will say:

(OPERATE )

Press:

COL

Run

until auger is dispensing.

Press:

ADD

Run

until

auger

is dispensing.

Press:

DUMP

This will

empty

the

weigh bin.

Now you can CALIBRATE EACH material.

To do so:

Press:

CAL

Display

will

say:

(CALIBRATE)

Press:

REG

REGRIND

will

calibrate itself.

For each material, press CAL followed by the proper component key. Each time a dispense will occur, followed by weighing, followed by a dump to empty the weigh bin.

Press:

EXIT

when all calibrations are done.

 

 

YOU ARE NOW READY FOR ACCURATE PRODUCTION BLENDING.

 

 

+---------------------------------------------------

 

 

+

 

¦

 

 

 

¦

 

¦ PROCEED TO:

SPECIAL INSTRUCTIONS

NEXT PAGE

¦

 

¦

 

 

 

¦

 

+---------------------------------------------------

 

 

+

Page 16

Image 15
Contents Gravimetric Blenders Date Manual Number UGB006/1103 Serial numbers Model numbers Part Operation Part Troubleshooting / SoftwarePart Hardware Maintenance Four Component SoftwareProceed to Safety Hazards Next Assembly InstructionsCheck OUT Procedure Special FeaturesAdditional MIX Blade Hazard Safety Hazards MIX BladesSafety Features Safety Interlock Switch Proceed to Assembly NextDisclaimers On the Next Part AssemblyLoad Cells are Easily Damaged Please Be CarefulPage Proceed to Check OUT Procedure Next Wiring ConsiderationsTouch Weigh BIN Very Lightly Procedure What should Happen Plug in ControllerTurn Power on AT this PointPress NAT KEY Press Alarm KEYPress REG KEY LED #Page Exit PasswordCAL Part Operation Load Cell CalibrationBe Sure CAL OFFCOL Proceed to Normal Operation NextOper OperateGB/WSB 240R Selected Models Special InstructionsMicro Pulse GB/WSB MBInstructions for Normal Operation If Problems DevelopPower OFF Power onNormal Operating Sequence Each Cycle Exit Regrind ROM OK Eight Character DisplayLED Lights Right Column AlarmsStrobe Light and Beeper Alarms Alarm SilenceMixer Motor ON/OFF/TIMED Switch Mixer Motor OutletMixer Motor Fuse Keypad Internal FusesDate RCP Keypad Automatic Operation ModeRecipe RUNSave BtchTABLE, FLG Page TAG FastALL Keypad Manual ModeTime ADD TimedPage Keypad Program Mode Para Star FunctionsYLD Ctrl Page Page Page Page Page Page Page Page Parameters Parameter List Brief ExplanationsMIX Time XXX RLO Page CPL Full Explanation of Parameters MPO No ALARM, no RetriesMIX BER KDF / WDFPage ROV Page Example RHL is Set 10 percent Page SET SettingPage Page Page Page Page XCV + XRC TCV + TRCXTP XUL XALPTD LIQMCT Page MPO RAL NAL CAL AAL MIX JOG Parameter Default Settings Four SoftwareFLG RPO NPO CPO APONTI NPT CPT APT RWTRTI NWTChanging Parameters Total Prnt OFFPrnt REG Natural COLFinal DISP,% What to Check for Page Page Page Calibrate Natural Special TestsTime Time NaturalCycles Last Printed 11/01/90 Material Usage InformationPARAMETER, PRT Date Time Totals Grand PCT CurrentPart IV Troubleshooting What to do Increasing Throughput Typical Problems Page Normal Operating Sequence Material Runs OUT Verifying Load Cell Function Load Cell RAW Signal Readout CNT OFFCNT Results to Expect Clear Routine Clear ALL RestartCore Dump Weigh BIN Dump Valve Soft Close Clean OUT Issues MIX Problems Page Full Recalibration of Load CellsZero WaitWeigh Bins Blender Preventive MaintenanceDispense Gates Load CellsThese Instructions for Totalizers only Totalize Special Totalizer FunctionStop END of Cycle BlenderComputer Outputs Wiring Supplement Call Appendix A-2 Gravimetric Batch Blenders Autoweigh GBM Series Models SpecificationsTOP View Front View Side View Gravimetric Batch Blenders AutoWeigh GB100 Series ModelsGravimetric Batch Blenders GB 220 and 420 Models 120V/1 phase/50-60 Hz 240V/1 phase/50-60 HzTOP View Mounting Interface Gravimetric Batch Blenders AutoWeigh GB240 and GB440 Models2124 Gravimetric Batch Blenders AutoWeigh GB900 Series ModelsGB1840 GB1860 Gravimetric Batch Blenders AutoWeigh GB1840 and 1860 ModelsControl Remote Mounted Models WSBM22 WSBM131 WSBM140 Gravimetric Batch Blenders Wsbm Series modelsSide View Front View Side View, R Model Front View, R Model Gravimetric Batch Blenders WSB 100 and 100R Models24.4 Gravimetric Batch Blenders WSB 220 and 420 ModelsWSB442 Gravimetric Batch Blenders WSB 240/440 and 240/440R ModelsGravimetric Batch Blenders WSB 1840, 1850 and 1860 Models Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C