TPBS005/0700
SPECIFICATIONS
GRAVIMETRIC BATCH BLENDERS
WSB 1840, 1850 and 1860 Models
C
B
Note: loader |
configuration |
same for all |
models |
CONTROL |
C |
A
MODELS |
|
| WSB1840 | WSB1850 | WSB1860 |
Performance characteristics |
|
|
|
| |
Batch size lbs {g} |
|
| 39.7 {18000} | 39.7 {18000} | 39.7 {18000} |
Maximum throughput lbs/hr {kg/hr}* | 4114 {1866} | 3160 {1433} | 2566 {1164} | ||
Bin Capacity - Main Ingredient | ft3 {liter} | 6.7 {189.7} | 6.7 {189.7} | 3.8 {107.6} | |
Bin Capacity - Minor Capacity | ft3 {liter} | 3.8 {107.6} | 3.8 {107.6} | 3.8 {107.6} | |
Maximum number of materials |
| 8 | 9 | 10 | |
Number of discharge valves |
| 4 | 5 | 6 | |
Number of additive feeders |
| up to 4 | up to 4 | up to 4 | |
Control Software (# of components) | 4 or 12 | 12 | 12 | ||
Dimensions inches {mm} |
|
|
|
| |
A - Height above mounting plate | 93 {2362.2} | 93 {2362.2} | 93 {2362.2} | ||
B - Width† |
|
| 56.25 {1428.8} | 56.25 {1428.8} | 56.25 {1428.8} |
C - Depth† |
|
| 34.4 {873.8} | 34.4 {873.8} | 34.4 {873.8} |
D - Controller height |
|
| 11.25 {285.75} | 11.25 {285.75} | 11.25 {285.75} |
E - Controller width |
|
| 12.25 {311.15} | 12.25 {311.15} | 12.25 {311.15} |
F - Controller depth |
|
| 8.19 {208.03} | 8.19 {208.03} | 8.19 {208.03} |
Weight lbs {kg} |
|
|
|
|
|
Installed |
|
| 730 {331} | 730 {331} | 730 {331} |
Shipping |
|
| 850 {385.5} | 850 {385.5} | 850 {385.5} |
Voltage Running load amps‡ |
|
|
|
| |
110V/1 phase/60hz | (control) |
| 0.3 | 0.3 | 0.3 |
220V/1 phase/60hz | (mixer) |
| 8.2 | 8.2 | 8.2 |
220V/1 phase/60hz | (control) |
| 0.2 | 0.2 | 0.2 |
220V/1 phase/60hz | (mixer) |
| 8.2 | 8.2 | 8.2 |
|
|
|
|
|
|
220V/1 phase/50hz | (control) |
| 0.2 | 0.2 | 0.2 |
220V/3 phase/50hz | (mixer) |
| 4.4 | 4.4 | 4.4 |
400V/3 phase/50hz | (mixer) |
| 2.2 | 2.2 | 2.2 |
Compressed air requirements |
|
|
|
| |
Discharge valves |
|
| 80 psi @ 0.2 ft3/min {5.5 bars @ 0.09 liters/sec} | ||
|
|
|
| 1/4 in. NPT fitting |
|
Maximum loader sizes § |
|
|
|
| |
Number of 20 inch loaders |
| 2 | 2 | 3 | |
Number of 15 inch loaders |
| 4 | 5 | 6 | |
|
|
|
|
|
|
MOUNTING INTERFACE
IB04 | (4) 9/16 in. {14.3 mm} |
| diameter bolt holes |
|
4 in. {101.6 mm} | 8 in. {203.2 mm} |
diameter | square bolt pattern |
through hole |
|
14.5 in. | 16 in. |
{406.4 mm} | |
{368.3 mm} |
|
15 in. {381 mm} | |
20 in. {508 mm} | |
SPECIFICATION NOTES:
*Maximum throughput rates are based on using all dispense valves and 35 lb/ft3 pelletized material. Use of feed- ers will reduce this rate.
†Feeders will increase width and depth dimensions. Please refer to feeder specifications.
‡Each auger feeder requires an addi- tional 1 amp @ 120V or 0.5 amp @ 240V.
§Maximum loader sizes may be used only when the loader is adjacent to loaders of a smaller diameter.
One Conair Drive ● Pittsburgh, PA 15202 ●
APPENDIX B