Henny Penny 680 KFC manual Press and release the Function button and MELT, Mode

Page 109

Henny Penny			Model 680
SMS SPECIAL PROGRAM	3.	Press and release the Function button and “MELT”, MODE
(Continued)		“CYCLE”, and “100s” shows alternately in the display,
		along	with the period (pulse) length of 4000. This should
		not be changed until the factory is consulted.
	4.	Press and release the Function button twice and “MELT”,
		“ON-”, “TIME”, and “100s”, shows alternately in the
		display, along with the length of time the heat is on. This
		should be set at 1700, and should not be changed until the
		factory is consulted.
	5.	Press and release the Function button three times and
		“COOL”, “SET-”, and “POINT” shows alternately in the
		display, along with the temperature at which the control
		exits	the melt cycle. This is set at 250º F (121º C), and
		should not be changed until the factory is consulted.
	6.	Press and release the Function button four times and
		“AUTO”, and “IDLE” shows alternately in the display,
		along with “OFF”. This should not be changed until the
		factory is consulted.
	7.	Press and release the Function button five times and
		“AUTO”, “IDLE”, and “MMSS” shows alternately in the
		display, along with “0:00”. This should not be changed
		until the factory is consulted.
	8.	The last 3 functions in the Heat Control mode are used by
		the factory only, and should not be changed.

6-36

1005

Image 109

Contents Page Henny Penny 8 Head GAS Pressure Fryer SpecificationsPage Page Limited Warranty for Henny Penny Appliances Introduction Section Pressure Fryer IntroductionPressure HeatPage Page Page Prop UP a Ramp for Each Caster on the Selected Side Insert Page Page Page ALL STR N Unit again after installation Shortening MAY Start UP Procedure Lever Is not to be Pulled Page Page Push handle back and raise lid Lo Mode Switches IndicatorsCool Mode Melt Cycle OperationHeat Light will illuminate whenever the control calls for Page Refer to KFC’s Standards Library on cleaning instructions Page 397 Connecw Hj i’.,‘i ,e.*f Page Product Color Not Correct Too Dark Spotted Rancid Taste Shortening Too old Pressure will not Eplace pressure plate Replace module Heating of shortening too slow Or boil Water Shortening Ing over Gasket coming out of lid Pressure System Page Page Pump Position Check from Page Panel Henny Penny Complete ControlPressure Regulation Every 90 daysPage Page Page Pressure PAD LID Counterweight CONT’DLID Adjustment Hertz Page Solenoid Valve ReplacementSeat Operating Control ValveRemoval & Cleaning Do not Manuallyactivate the SafetySafety Valve Operating ControlPressure Gauge Do not Disassemble or Modify this VavleCalibration Steps Page Page Page Page Page Page Page Page Page Using 3/8 socket, remove nut securing ground wire If no red glow is seen, proceed with the following Page Page Page Epyg-ui nuebq plea ewy Page Page Page Page Product One Part PER Number Description Assy UnitsLatch Plate PANEL, Right Side Page Not Avail Page Part PER Number Description Counterweight BARCable CarriageHenny Penny Model 1005 Units Part PER Number Description Assy LinkageassemblyLID Instruction Label CAM Slide FillerPage 705 Page Fitting Connector Dead WeightPressure Gauge Pipe ELBOW, 1/4Page SUPPORT, Drain ROD LINK, Drain RODBRACKET, HI-LIMIT HI-LIMITPage Units Smooth and Rounded Edge of Blade CORE, Disc Assembly Solenoid ValveassemblyCOVER, Coil Housing HOUSING, CoilHead GAS Cooker I I SIE IAy--4A-+-7 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 IfApplicable SMS ProgrammingCode After the load compensation, press and release the Func Review Usage SMS Special ProgramMode Factory Presets F/C, Gas/Electric, Speaker Volume Reset UsageMode Speaker Frequency, Codes, Initialize SystemAppliance Test Tech I/O ModeHeat Control Press and release the Function button and MELT, Mode