Henny Penny 35200 Umbrella Grommet and Other Essential Parts

Page 90

Henny PennyModel 680

FIGURE				UNITS
& ITEM		PART		PER
	NO.	NUMBER	DESCRIPTION	ASSY.

√	1	16910	PRESSURE GAUGE	1
	2	16909	PIPE ELBOW, 1/4”	1
√	3	16908	PIPE NIPPLE, 1/4”	1
√	4	59742	RELIEF VALVE	1
	5	FP01-063	REDUCER, 1/2 NPT M TO 1/4 NPT F	1
	6	FP01-011	PIPE TEE	2
	7	FP01-028	NIPPLE, Close 1/2 Male Elbow	2
	8	17407	CONNECTOR, 1/2 Male Elbow	3
	9	16817	FITTING, Sleeve Teflon	*
	10	16809	NUT FITTING	*
	11	16926	CAP, Dead Weight ValveAssy	1
	12	16902	SEAL “O” RING	1
	13	16903	DEAD WEIGHT	1
	14	16918	ORIFICE, 12 PSI	1
	15	16852	BODY, Valve	1
	16	35686	TUBE, DW to Exhaust Stack	1
	17	35817	PIPE NIPPLE, 1/2 x 2 1/4 SS	1
	18	16804	UMBRELLA GROMMET	1
	19	35200	UMBRELLA GROMMET	1
	20	35474	PIPE NIPPLE, 1/2 x 2	1
	21	FP01-066	COUPLING, 1/2 NPT SS	1
	22	16807	FITTING CONNECTOR	1
	23	35147	TUBE, Steam Exhaust - Up	1
	24	17121	VALVE, Solenoid	1
	25	16808	FITTING SLEEVE, Steel	1

√recommended parts

206

6-17

Image 90

Contents Page Specifications Henny Penny 8 Head GAS Pressure FryerPage Page Limited Warranty for Henny Penny Appliances Introduction Section Pressure IntroductionPressure Fryer HeatPage Page Page Prop UP a Ramp for Each Caster on the Selected Side Insert Page Page Page ALL STR N Unit again after installation Shortening MAY Start UP Procedure Lever Is not to be Pulled Page Page Push handle back and raise lid Cool Mode Switches IndicatorsLo Mode Melt Cycle OperationHeat Light will illuminate whenever the control calls for Page Refer to KFC’s Standards Library on cleaning instructions Page 397 Connecw Hj i’.,‘i ,e.*f Page Product Color Not Correct Too Dark Spotted Rancid Taste Shortening Too old Pressure will not Eplace pressure plate Replace module Heating of shortening too slow Or boil Water Shortening Ing over Gasket coming out of lid Pressure System Page Page Pump Position Check from Page Pressure Regulation Complete ControlPanel Henny Penny Every 90 daysPage Page Page LID Counterweight CONT’D Pressure PADLID Adjustment Hertz Page Seat ReplacementSolenoid Valve Operating Control ValveSafety Valve Do not Manuallyactivate the SafetyRemoval & Cleaning Operating ControlDo not Disassemble or Modify this Vavle Pressure GaugeCalibration Steps Page Page Page Page Page Page Page Page Page Using 3/8 socket, remove nut securing ground wire If no red glow is seen, proceed with the following Page Page Page Epyg-ui nuebq plea ewy Page Page Page Page Product One Units Part PER Number Description AssyLatch Plate PANEL, Right Side Page Not Avail Page Cable Counterweight BARPart PER Number Description CarriageHenny Penny Model 1005 LID Instruction Label LinkageassemblyUnits Part PER Number Description Assy CAM Slide FillerPage 705 Page Pressure Gauge Dead WeightFitting Connector Pipe ELBOW, 1/4Page BRACKET, HI-LIMIT LINK, Drain RODSUPPORT, Drain ROD HI-LIMITPage Units Smooth and Rounded Edge of Blade COVER, Coil Housing Solenoid ValveassemblyCORE, Disc Assembly HOUSING, CoilHead GAS Cooker I I SIE IAy--4A-+-7 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 SMS Programming IfApplicableCode After the load compensation, press and release the Func SMS Special Program Review UsageMode Mode Reset UsageFactory Presets F/C, Gas/Electric, Speaker Volume Speaker Frequency, Codes, Initialize SystemTech I/O Mode Appliance TestHeat Control Press and release the Function button and MELT, Mode