Henny Penny 680 KFC manual Henny Penny 8 Head GAS Pressure Fryer, Specifications

Page 2

Henny Penny

Model 680

HENNY PENNY 8 HEAD GAS PRESSURE FRYER

Model 680 Gas Fryer

SPECIFICATIONS
Height	60" (152.4 cm)
Width	24" (61 cm)
Depth	41½" (106 cm)
Floor Space	Approximately 7 sq. ft. (.65 sq. m.)
Pot Capacity	8 Head of chicken (24 lbs.)(10.9 Kg.)
	95 lbs. shortening (40.86 Kg.)
Electrical	120 VAC, 1 Phase, 50/60 Hz, 10 Amp, 3 Wire Service
Heating	Propane or Natural Gas; 100,000 BTU/Hr.(29.3 Kw)
Pressure	12 PSI operating pressure (827 mbar)
	14.5 PSI safety relief pressure (999 mbar)
ShippingWeight	Approximately 800 lbs. (360 Kg.)
Accessories Shipped	Five 1/2 size pan racks and carrier.

NOTE

Adata plate, located on the right side panel, gives the information of the type of fryer, serial number, warranty date, and other information pertaining to fryer.

FM01-320

Revised 02-20-06

Image 2

Contents Page Specifications Henny Penny 8 Head GAS Pressure FryerPage Page Limited Warranty for Henny Penny Appliances Introduction Section Pressure IntroductionPressure Fryer HeatPage Page Page Prop UP a Ramp for Each Caster on the Selected Side Insert Page Page Page ALL STR N Unit again after installation Shortening MAY Start UP Procedure Lever Is not to be Pulled Page Page Push handle back and raise lid Cool Mode Switches IndicatorsLo Mode Melt Cycle OperationHeat Light will illuminate whenever the control calls for Page Refer to KFC’s Standards Library on cleaning instructions Page 397 Connecw Hj i’.,‘i ,e.*f Page Product Color Not Correct Too Dark Spotted Rancid Taste Shortening Too old Pressure will not Eplace pressure plate Replace module Heating of shortening too slow Or boil Water Shortening Ing over Gasket coming out of lid Pressure System Page Page Pump Position Check from Page Pressure Regulation Complete ControlPanel Henny Penny Every 90 daysPage Page Page LID Counterweight CONT’D Pressure PADLID Adjustment Hertz Page Seat ReplacementSolenoid Valve Operating Control ValveSafety Valve Do not Manuallyactivate the SafetyRemoval & Cleaning Operating ControlCalibration Steps Do not Disassemble or Modify this VavlePressure Gauge Page Page Page Page Page Page Page Page Page Using 3/8 socket, remove nut securing ground wire If no red glow is seen, proceed with the following Page Page Page Epyg-ui nuebq plea ewy Page Page Page Page Product One Units Part PER Number Description AssyLatch Plate PANEL, Right Side Page Not Avail Page Cable Counterweight BARPart PER Number Description CarriageHenny Penny Model 1005 LID Instruction Label LinkageassemblyUnits Part PER Number Description Assy CAM Slide FillerPage 705 Page Pressure Gauge Dead WeightFitting Connector Pipe ELBOW, 1/4Page BRACKET, HI-LIMIT LINK, Drain RODSUPPORT, Drain ROD HI-LIMITPage Units Smooth and Rounded Edge of Blade COVER, Coil Housing Solenoid ValveassemblyCORE, Disc Assembly HOUSING, CoilHead GAS Cooker I I SIE IAy--4A-+-7 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Code SMS ProgrammingIfApplicable After the load compensation, press and release the Func Mode SMS Special ProgramReview Usage Mode Reset UsageFactory Presets F/C, Gas/Electric, Speaker Volume Speaker Frequency, Codes, Initialize SystemHeat Control Tech I/O ModeAppliance Test Press and release the Function button and MELT, Mode