Henny Penny 680 KFC manual Not Avail

Page 82

Henny Penny

Model 680

FIGURE				UNITS
& ITEM		PART		PER
	NO.	NUMBER	DESCRIPTION	ASSY

√	1	Not Avail.	POT & COUNTERTOPASSY	1
√	2	35487	BURNER, Infrared	2
	3	35940	INSULATION, BurnerSide	4
	3	35941	INSULATION, Burner Top & Bottom	4
	4	36753	RETAINER, Burner Side	4
	5	35376	RETAINER, Burner Top	2
	6	WA01-007	WASHER	1
	7	NS02-005	HEXNUT	25
	8	35246	ORIFICE, Natural	2
	9	35504	HOSE	1
	10	35504	HOSE	1
	11	35846	GAS LINE TEE TO ORIFICE, Right	1
	12	FP01-075	FITTING, 3/8- 1/2" NPT	2
	13	FP01-074	FITTING, 3/8- 1/4" NPT	4
	14	16909	ELBOW, 90°	2
	15	FP01-011	TEE	1
	16	16808	FITTING	1
	17	16809	FITTING	1
	18	35507	TUBE, Gas Valve to Tee	1
	19	17407	ELBOW, 90°	2
	20	35508	GAS LINE TEE TO ORIFICE, Left	1
√	21	35268	ORIFICE, Propane	2
√	22	14058	PROBE ASSEMBLY, Kit - Non-SMS	1
√	22	14373	PROBE ASSEMBLY, Kit - SMS	1
√	23	16727	HIGH LIMIT CONTROL	1
	24	NS02-006	HEXNUT	2
	25	NS02-006	HEXNUT	2
√	26	35889	COVER, Front Probe	1
√	27	16727	HIGH LIMIT CONTROL	1
√	28	38466	IGNITOR and BRACKET ASSY.,
√			SN:DHO01IB and above (Not Shown)	2
√	29	38568	REMOTE SENSOR (Not Shown)	2

√recommended parts

206

6-9

Image 82

Contents Page Specifications Henny Penny 8 Head GAS Pressure FryerPage Page Limited Warranty for Henny Penny Appliances Introduction Section Pressure IntroductionPressure Fryer HeatPage Page Page Prop UP a Ramp for Each Caster on the Selected Side Insert Page Page Page ALL STR N Unit again after installation Shortening MAY Start UP Procedure Lever Is not to be Pulled Page Page Push handle back and raise lid Cool Mode Switches IndicatorsLo Mode Melt Cycle OperationHeat Light will illuminate whenever the control calls for Page Refer to KFC’s Standards Library on cleaning instructions Page 397 Connecw Hj i’.,‘i ,e.*f Page Product Color Not Correct Too Dark Spotted Rancid Taste Shortening Too old Pressure will not Eplace pressure plate Replace module Heating of shortening too slow Or boil Water Shortening Ing over Gasket coming out of lid Pressure System Page Page Pump Position Check from Page Pressure Regulation Complete ControlPanel Henny Penny Every 90 daysPage Page Page LID Counterweight CONT’D Pressure PADLID Adjustment Hertz Page Seat ReplacementSolenoid Valve Operating Control ValveSafety Valve Do not Manuallyactivate the SafetyRemoval & Cleaning Operating ControlPressure Gauge Do not Disassemble or Modify this VavleCalibration Steps Page Page Page Page Page Page Page Page Page Using 3/8 socket, remove nut securing ground wire If no red glow is seen, proceed with the following Page Page Page Epyg-ui nuebq plea ewy Page Page Page Page Product One Units Part PER Number Description AssyLatch Plate PANEL, Right Side Page Not Avail Page Cable Counterweight BARPart PER Number Description CarriageHenny Penny Model 1005 LID Instruction Label LinkageassemblyUnits Part PER Number Description Assy CAM Slide FillerPage 705 Page Pressure Gauge Dead WeightFitting Connector Pipe ELBOW, 1/4Page BRACKET, HI-LIMIT LINK, Drain RODSUPPORT, Drain ROD HI-LIMITPage Units Smooth and Rounded Edge of Blade COVER, Coil Housing Solenoid ValveassemblyCORE, Disc Assembly HOUSING, CoilHead GAS Cooker I I SIE IAy--4A-+-7 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 IfApplicable SMS ProgrammingCode After the load compensation, press and release the Func Review Usage SMS Special ProgramMode Mode Reset UsageFactory Presets F/C, Gas/Electric, Speaker Volume Speaker Frequency, Codes, Initialize SystemAppliance Test Tech I/O ModeHeat Control Press and release the Function button and MELT, Mode