Henny Penny 680 KFC manual Product One

Page 77

Product One		Pressure	Solenoid
		and Neat	Control
Select Time		Product	Indicators
Select Function		Function	Indicators
Change Button		Change Button
Under Display	4	Indicator	Display
Change Button		Change Button
Under Display	3	Indicator	Display
Change Button		Change Button
Under Display	2	Indicator	Display
Change Button		Change Button
Under Display	1	Indicator	Display

The SELECT FUNCTION or SELECT TIME button must be depressed before the PRODUCT ONE button to properly perform the solenoid and heat control output test.

For short durati		perate without
temperature	regulation,	or will overheat the
shortening.

When programming one-step KFC parameters, load compen- sation and proportional control are automatically programmed into the control. The following defines these two functions.

-Load compensation adjusts cooking sate for differences in the cooking process such

as load size. The control is continuously comparing the pot temperature to the setpoint temperature. If the pot temperature is above the setpoint, the control will shorten the cook time. If the pot temperature is below the setpoint, the control will lengthen the cook time. Load compensation for KFC parameters is set at 0.

=Proportional control regulates pot the heat on and off until it reaches

setpoint temperature. This allows better temperature accuracy when dropping product. Proportional control for KFC parameters is set at 10 degrees.

Image 77

Contents Page Henny Penny 8 Head GAS Pressure Fryer SpecificationsPage Page Limited Warranty for Henny Penny Appliances Introduction Section Pressure Fryer IntroductionPressure HeatPage Page Page Prop UP a Ramp for Each Caster on the Selected Side Insert Page Page Page ALL STR N Unit again after installation Shortening MAY Start UP Procedure Lever Is not to be Pulled Page Page Push handle back and raise lid Lo Mode Switches IndicatorsCool Mode Melt Cycle OperationHeat Light will illuminate whenever the control calls for Page Refer to KFC’s Standards Library on cleaning instructions Page 397 Connecw Hj i’.,‘i ,e.*f Page Product Color Not Correct Too Dark Spotted Rancid Taste Shortening Too old Pressure will not Eplace pressure plate Replace module Heating of shortening too slow Or boil Water Shortening Ing over Gasket coming out of lid Pressure System Page Page Pump Position Check from Page Panel Henny Penny Complete ControlPressure Regulation Every 90 daysPage Page Page Pressure PAD LID Counterweight CONT’DLID Adjustment Hertz Page Solenoid Valve ReplacementSeat Operating Control ValveRemoval & Cleaning Do not Manuallyactivate the SafetySafety Valve Operating ControlCalibration Steps Do not Disassemble or Modify this VavlePressure Gauge Page Page Page Page Page Page Page Page Page Using 3/8 socket, remove nut securing ground wire If no red glow is seen, proceed with the following Page Page Page Epyg-ui nuebq plea ewy Page Page Page Page Product One Part PER Number Description Assy UnitsLatch Plate PANEL, Right Side Page Not Avail Page Part PER Number Description Counterweight BARCable CarriageHenny Penny Model 1005 Units Part PER Number Description Assy LinkageassemblyLID Instruction Label CAM Slide FillerPage 705 Page Fitting Connector Dead WeightPressure Gauge Pipe ELBOW, 1/4Page SUPPORT, Drain ROD LINK, Drain RODBRACKET, HI-LIMIT HI-LIMITPage Units Smooth and Rounded Edge of Blade CORE, Disc Assembly Solenoid ValveassemblyCOVER, Coil Housing HOUSING, CoilHead GAS Cooker I I SIE IAy--4A-+-7 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Code SMS ProgrammingIfApplicable After the load compensation, press and release the Func Mode SMS Special ProgramReview Usage Factory Presets F/C, Gas/Electric, Speaker Volume Reset UsageMode Speaker Frequency, Codes, Initialize SystemHeat Control Tech I/O ModeAppliance Test Press and release the Function button and MELT, Mode